TYM T194 Скачать руководство пользователя страница 13

Страница: 13 / 169

- 1

SAFeTY PReCAUTIONS

T72O211A

Use of hazard warning lights and

turn signals are recommended when

towing equipment on public roads

unless prohibited by state or local

regulations.
Use slow moving vehicle (SMV) sign

when driving on public road during

both day & night time, unless pro-

hibited by law.

ALWAYS USe SAFeTY LIGHTS AND

DeVICeS

T72O212A

Understand service procedure be-

fore doing work.
Keep the surrounding area of the

Ride on lawnmower clean and dry.
Do not attempt to service Ride on

lawnmower when it is in motion.
Keep body and clothing away from

rotating shafts.
Always lower equipment to the

ground. Stop the engine.
Remove the key. Allow Ride on

lawnmower to cool before any work

repair is caused on it.

PRACTICe SAFe MAINTeNANCe

Securely support any Ride on lawn-

mower elements that must be raised

for service work.
Keep all parts in good condition and

properly installed.
Replace worn or broken parts. Re-

place damage/missing decals.
Remove any buildup of grease or oil

from the Ride on lawnmower.
Disconnect battery ground cable(-)

before making adjustments on elec-

trical systems or welding on Ride on

lawnmower.

T194(K0) RIDE ON LAWNMOWER-영문-0113 13

2018-08-13 오후 4:23:01

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Бренды по названию

Популярные бренды