TYM T194 Скачать руководство пользователя страница 48

Страница: 48 / 169

2 - 10

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

(9) Coolant temperature warning lamp

If this lamp comes on, coolant

is overheated.

Coolant temperature warning lamp

When the coolant temperature

warning lamp comes on, cool-

ant is overheated so check the

coolant.

•

NOTE

PTO ON/OFF SwITCH

PTO ON/OFF switch is situated on

the right hand side on the instru-

ment panel and can be identified

easily with its built in yellow colored

indicator.
When the switch is pushed down

to start the PTO indicator glows to

indicate that the switch and the PTO

are in ON position.
If the switch is pushed down and

turn counter clock wise the indicator

goes off signaling that the PTO is

OFF.

►

PTO ON/OFF

switch

T19O116A

(10) Engine warning lamp It comes on

when the engine is malfunctioning.

Engine warning lamp

When Engine warning lamp is

it, ensure that you operator the

Ride on lawnmower only after

the engine RPM reaches at the

normal speed if this instruction

is not kept, it may cause a per-

formance degradation or acci-

dent due to a system error.

•

CaUTION

T194(K0) RIDE ON LAWNMOWER-영문-0210 10

2018-07-03 오후 3:49:16

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Бренды по названию

Популярные бренды