manualshive.com logo in svg

TYM T194, Руководство пользователя

Поделиться
Скачать
TYM T194 Скачать руководство пользователя страница 35

1

1 - 5

GENERAL INFORMATION

2. SAFETY SIGNS

 

In order to work with the machine safely, safety decals are placed on the machine.

 

Make sure to read and follow the directions.

■

 

Keep the safety decals clean and undamaged at all times.

If a safety decal on the machine is dirty, wash it with soapy water and wipe it off with a soft cloth.
Never use solution as thinner or acetone because these can erase characters or pictures.

■

 If washed with high-pressured water, a decal may be peeled off.

Do not apply high-pressured water directly onto decals. 

■

 If a safety decal is damaged or lost, order a new one immediately and place it on  

   the machine.

When putting a new decal, wipe off the place to post the decal thoroughly and wait until it is dried. Then 
post the decal.
Each decal has a part number on the bottom.

■

 When replacing a part attached with a decal with a new part, replace the decal as  

   well.

T194(K0) RIDE ON LAWNMOWER-영문-015   5

2018-08-13   오후 4:46:27

Содержание T194










































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды