Tsuruga 8527 Скачать руководство пользователя страница 24

Страница: 24 / 112

Setting of test condition for withstanding voltage test

[When setting the referential voltage]

To enter setting mode

①

In READY status, press

key, then the test mode lamp blinks.

Test mode lamp moves up and down with

▲

▼

key. Make the required test

mode lamp blinking (

W-I

I-W

lamp).

②

Press

key and make the test mode lamp lit.

Setting of referential voltage

①

Press

key and select the status that the

W AC

lamp is lit up, the test

voltage range display is lit up with

and the test voltage display blinks.

②

Next, press

ON/OFF

key and select the status that the display blinks with the

numeral.

③

Press

▲

▼

key and set the referential voltage.

Pressing of

key (

SHIFT

and

▲

at a time) or

key (

SHIFT

and

▼

at a time) allows the setting of second digit (the digit of 0.10kV)

(refer to the above figure).

Note

: The referential voltage can be set within the range of 0.00~5.00kV.

To move to the previous setting

Press

key, then the setting changes to the

setting of slider voltage

To the next setting

Press

key, then changes to the

setting of high limit of leak current

Finish of setting

Press

ENTER

key, then the slider moves up or down and the tester returns to READY

status, memorizing the set having been made.
When the

EXIT

key (

SHIFT

and

ENTER

at a time) is pressed in the setting mode,

the setting mode for the test condition is interrupted and the tester becomes READY
status.

The test conditions in this case are those before entering the setting mode of test condition.

ON/OFF

ENTER

WRITE

READ

LOCK

○

BUZZER

READY

REMOTE

DISCHARGE

KEY LOCK

EXIT

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

SHIFT

LOW

GOOD

HIGH

LOW

GOOD

HIGH

LOW

○

W-TEST

○

MEMORY

SET

No.

○

I-TEST

I-W

W-I

HIGH

●

VOLTAGE SLIDER

Содержание 8527

















































































































Результаты поиска

Содержание 8527

Отзывы:

Похожие инструкции для 8527

Бренды по названию

Популярные бренды

Tsuruga 8527, Инструкция по эксплуатации

Результаты поиска

Содержание 8527

Отзывы:

Похожие инструкции для 8527

Бренды по названию

Популярные бренды