Tsuruga 8527 Скачать руководство пользователя страница 43

Страница: 43 / 112

I test

11.2

●

I test (insulation resistance test)

(1) In READY status, press

key, then the test mode lamp blinks.

Select the

lamp with

▲

▼

key, and the test conditions are also displayed.

(2) When it is necessary, the test conditions can be changed with

▲

▼

ON/OFF

SHIFT

key. For detail, refer to the article 9.

Note

: The test time can be set to

. In this case, the elapsed time is displayed

during the test, and when exceeded 999s, the display scrolls with

while the test is continued.

(3) Press

START

switch

③

, then

I-TEST

lamp is lit up and the test starts.

While the high voltage is output, the

DANGER

lamp is lit up.

During the test,

TEST/H.V.OUT

I-TEST

TEST

REMOTE/OUT

connector

are

turned ON and

READY

is OFF.

When the test is finished,

TEST/H.V.OUT

I-TEST

TEST

REMOTE/OUT

connector

are turned OFF and

END

is ON.

(4) Case of good judgement

When the test time is elapsed, the test finishes and the

GOOD

of insulation

resistance test is lit up.

●

When the good judgement time is for 0.2 seconds, the tester returns to READY

status before the start.

●

When the good judgement time is continuous output, re-start is not possible.

In this case, press

STOP

switch

②

, then it becomes READY status.

●

For the judgement output,

I-GOOD

GOOD

REMOTE/OUT

connector

are

turned ON.

(5) Case of NG judgement

The output of test voltage is stopped and the test is stopped.

When the measured

resistance value becomes out of the set range, the output of test voltage is stopped and
the test is also stopped. When the measured resistance value is higher than the high
limit value,

JUDGE HIGH

is, and when the value is lower than the low limit value,

JUDGE LOW

is lit up.

Press

STOP

switch

②

, then it becomes READY status.

●

For the judgement output,

I-HIGH

I-LOW

REMOTE/OUT

connector

are turned ON.

○

READY

REMOTE

DISCHARGE

KEY LOCK

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

GOOD

HIGH

LOW

GOOD

HIGH

LOW

W-TEST

○

MEMORY

SET

No.

○

I-TEST

I-W

W-I

HIGH

LOW

●

○

READY

REMOTE

DISCHARGE

KEY LOCK

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

HIGH

LOW

GOOD

HIGH

LOW

W-TEST

○

MEMORY

SET

No.

○

I-TEST

I-W

W-I

HIGH

LOW

●

GOOD

○

READY

REMOTE

DISCHARGE

KEY LOCK

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

HIGH

GOOD

HIGH

LOW

W-TEST

○

MEMORY

SET

No.

○

I-TEST

I-W

W-I

HIGH

LOW

●

○

GOOD

LOW

Содержание 8527

















































































































Результаты поиска

Содержание 8527

Отзывы:

Похожие инструкции для 8527

Бренды по названию

Популярные бренды

Tsuruga 8527, Инструкция по эксплуатации

Результаты поиска

Содержание 8527

Отзывы:

Похожие инструкции для 8527

Бренды по названию

Популярные бренды