Tsuruga 8527 Скачать руководство пользователя страница 28

Страница: 28 / 112

Setting of test condition for withstanding voltage test

8.5

●

Test time

Adjustable range: 0.5~999 s

When the test mode is W, the test time can be switched OFF.

Note

: When the test mode is W-I or I-W, please set the test time.

[When switching OFF the setting of test time]

To enter setting mode

①

In READY status, press

key, then the test mode lamp blinks.

Test mode lamp moves up and down with

▲

▼

key. Make the

test mode

lamp blinking.

②

Press

key and make the test mode lamp lit.

To turn OFF the setting of test time

①

Press

key and select the status that the test time display blinks.

②

Next, press

ON/OFF

key and select the status that the display blinks with

(refer to the above figure).

To move to the previous setting

Press

key, then the setting changes to the

setting of low limit of leak current

To the next setting

Press

key and the setting changes as follows depending upon the test mode.

Test mode

Setting item after change

W-I

→

Setting of test voltage for insulation resistance test.

→

Returns to the blinking of

test mode lamp.

I-W

→

Returns to the blinking of

I-W

test mode lamp.

Finish of setting

Press

ENTER

key, then the slider moves up or down and the tester returns to READY

status, memorizing the set having been made.
When the

EXIT

key (

SHIFT

and

ENTER

at a time) is pressed in the setting mode,

the setting mode for the test condition is interrupted and the tester becomes READY
status.

The test conditions in this case are those before entering the setting mode of test condition.

ON/OFF

ENTER

WRITE

READ

LOCK

○

BUZZER

READY

REMOTE

DISCHARGE

KEY LOCK

EXIT

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

SHIFT

GOOD

HIGH

LOW

GOOD

HIGH

LOW

○

W-TEST

○

MEMORY

SET

No.

○

I-TEST

I-W

W-I

●

HIGH

LOW

○

●

VOLTAGE SLIDER

Содержание 8527

















































































































Результаты поиска

Содержание 8527

Отзывы:

Бренды по названию

Популярные бренды

Tsuruga 8527, Инструкция по эксплуатации

Результаты поиска

Содержание 8527

Отзывы:

Бренды по названию

Популярные бренды