Tsuruga 8527 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 112

Tsuruga 8527 Скачать руководство пользователя страница 50

50

Remote control

14.4

●

Operation by REAR:MODE

Features of REAR:MODE

1. The test mode (withstanding voltage or insulation resistance test) can be selected by a

relay, sequencer etc. When the test mode is not selected, the test is performed by the
test condition before entering the REAR:MODE.

2. The test can be done, reading out the content of memory setting by a sequencer etc.

3. The test mode can be externally controlled but the change of numeral setting is not

possible, so make the setting in advance by the memory etc.

4. Since the tester is used by the external control, the tester becomes key lock condition

during the setting.

5. The start signal is decided depending upon the setting condition of remote control.

6. An interruption of the test is possible from the

STOP

switch

②

,

STOP

terminal

, on the rear panel and

Pin No.4 (STOP) of the

REMOTE/OUT

connector.

REAR:MODE from the setting to the start

(1) Make a short-circuit between the Pin No.20 (REAR:MODE) of the

REMOTE/OUT

connector

on the rear and COM (either 19, 23 or 36) of the same connector

.

is displayed on the memory number display.

Note

: When auto operation is done by the sequencer etc. without using the

START

switch

③

(manual start), make the Pin No.2 (REAR:ON) ON. Or, make a

short-circuit between REAR:ON and C of the

REMOTE

terminal

.

(2) Select a test mode.

Make a selection of either test mode in advance, withstanding voltage or insulation
resistance test, by means of Pin No.21 (W-MODE) or Pin No.22 (I-MODE) on the

REMOTE/OUT

connector

.

(3) After confirming the wiring with the test sample, safety and so on, press

START

switch

③

. Or, start the test by remote control.

In order to do the withstanding voltage and insulation resistance test in sequence (W-I,
I-W), make a re-start switching over the other test mode, after the good judgement at the
item (2) above.
[Example] When the withstanding voltage test

→

insulation resistance test (W-I) is done.

①

In READY status, turn ON the Pin No.21 (W-MODE) of the

REMOTE/OUT

connector

. The test is started. The tester becomes in operation of

withstanding voltage test and the

DANGER

lamp

⑬

is lit up.

②

After the good judgement of withstanding voltage test, turn OFF the Pin No.21
(W-MODE). The tester is then in READY status.

③

To do the insulation resistance test next, turn ON the Pin No.22 (I-MODE).

④

Start the test. The tester becomes in operation of insulation resistance test and
the

DANGER

lamp

⑬

is lit up.

⑤

Afterwards, the judgement can be made normally.

To start reading out the memory

(1) Make a short-circuit between the Pin No.20 (REAR:MODE) of the

REMOTE/OUT

connector

on the rear and COM (either 19, 23 or 36) of the same connector

.

is displayed on the memory number display.

(2) By the combination of the BCD code of the Pin No.6~9 (MEM SET 1, 2, 4, 8) of the

same connector

, read out the memory No.1~9.

Note

: When the A~F code is input, A~F is displayed on the display but no read out

is possible.

(3) After confirming the wiring with the test sample, safety and so on, press

START

switch

③

. Or, start the test by remote control.

Remote control which can be jointly used with REAR:MODE

Basically, it is as explained at the REAR:MODE from the setting to the start .

During the REAR:MODE setting, the remote control can also be used jointly.
The start from the

REMOTE

connector

⑧

(front panel),

REMOTE

terminal

(rear

panel) and Pin No.3 (START) of the

REMOTE/OUT

connector

is also possible.

Refer to the article 14.6 for the priority of remote control.

[Likely error at the REAR:MODE]

Blinking display of

For a likely cause and solution, refer to the
article 20 Error messages.

Blinking display of

Blinking display of

«
...
48
49
50
51
52
...
»

Содержание 8527

















































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды