Tsuruga 8527 Скачать руководство пользователя страница 26

Страница: 26 / 112

Setting of test condition for withstanding voltage test

8.4

●

Low limit of leak current

Adjustable range: 0.0~109.0mA, OFF.

Note-1

: The low limit value of leak current can not be higher than that of high limit, so

please apply either corrective solution below:

1. When the low limit value is determined, set the high limit value to exceed the

value of low limit.

2. When the high limit value is determined, set the low limit value not to exceed

the value of high limit.

Note-2

: When the setting is turned OFF, no judgement for the low limit is made.

When the setting is restored (ON) from

, and when the low limit value is

higher than the high limit value, the low limit value is replaced with 0.0mA.

[When turning OFF the setting of low limit of leak current]

To enter setting mode

①

In READY status, press

key, then the test mode lamp blinks.

Test mode lamp moves up and down with

▲

▼

key. Make the required test

mode lamp blinking (

W-I

I-W

lamp).

②

Press

key and make the test mode lamp lit.

To turn OFF the setting of low limit of leak current

①

Press

key and select the status that the current/resistance display blinks,

the

is lit up and the

LOW SET

is also lit.

②

Next, press

ON/OFF

key and select the status that the display blinks with

(refer to the above figure).

To move to the previous setting

Press

key, then the setting changes to the

setting of high limit of leak current

To the next setting

Press

key, then changes to the

setting of test time

Finish of setting

Press

ENTER

key, then the slider moves up or down and the tester returns to READY

status, memorizing the set having been made.
When the

EXIT

key (

SHIFT

and

ENTER

at a time) is pressed in the setting mode,

the setting mode for the test condition is interrupted and the tester becomes READY
status.

The test conditions in this case are those before entering the setting mode of test condition.

ON/OFF

ENTER

WRITE

READ

LOCK

○

BUZZER

READY

REMOTE

DISCHARGE

KEY LOCK

EXIT

AC TEST VOLTAGE

MODE

JUDGE

TIME

RANGE

CURRENT/RESISTANCE

SHIFT

GOOD

HIGH

LOW

GOOD

HIGH

LOW

○

W-TEST

○

MEMORY

SET

No.

○

I-TEST

I-W

W-I

●

HIGH

LOW

VOLTAGE SLIDER

Содержание 8527

















































































































Результаты поиска

Содержание 8527

Отзывы:

Похожие инструкции для 8527

Бренды по названию

Популярные бренды

Tsuruga 8527, Инструкция по эксплуатации

Результаты поиска

Содержание 8527

Отзывы:

Похожие инструкции для 8527

Бренды по названию

Популярные бренды