Tsuruga 8527 Скачать руководство пользователя страница 80

Страница: 80 / 112

Explanation of command

4.2.7

RESPONSE=

(setting of response)

Function

When 8527 received the effective command, it informs the host that the
command is normally received. This communication function can be
set to ON or OFF.

Structure

RESEPONSE=

ON/OFF

ON/OFF : Always transmits the response with “ON”.

When 8527 receives the effective command, it transmits

ERROR=0

to the host.

For the ineffective command, it transmits

ERROR= No

When 8527 receives the effective command with “OFF”,
no response is transmitted to the host.
When the command is ineffective,

ERROR= No

transmitted regardless of ON/OFF of the Response
Setting.

Note

For

ERROR= No

, refer to the article 6 Error.

Transmission

RESEPONSE=ON



……… Makes the response setting ON.

RESEPONSE=OFF



.……. Makes the response setting OFF.

Response

When 8527 received the effective command setting.

ERROR=0



…….………. When the Response Setting is ON.

No response ……………….. When the Response Setting is OFF.

4.2.8

RESEPONSE?

(read-out of setting of response)

Function

Reads out whether the setting of response is ON or OFF.

Structure

RESEPONSE?

Transmission

RESEPONSE?



Response

RESEPONSE=ON



……… When the Response Setting is ON.

RESEPONSE=OFF



…….. When the Response Setting is OFF.

Содержание 8527

















































































































Результаты поиска

Содержание 8527

Отзывы:

Похожие инструкции для 8527

Бренды по названию

Популярные бренды

Tsuruga 8527, Инструкция по эксплуатации

Результаты поиска

Содержание 8527

Отзывы:

Похожие инструкции для 8527

Бренды по названию

Популярные бренды