tousek TPS 20 Скачать руководство пользователя

Страница: 31 / 48

tousek

/ E_TPS-20_03 / 30. 08. 2016

- 31 -

Factory settings

Putting into operation

Sliding gate operator TPS 20, -20N, -20PRO

Important: preparation works

• All electrical installations (control panels, safety devices ...) have to be made in full conformity with the applying rules

and laws.

Attention: if no stop switch is connected then the terminals 30/31 have to be bridged.

•

The mechanical limits have to be placed so that contact edges are not triggered, as this would lead to an error
message

• Unlock emergency release of operator and set gate to half-opened position. Then lock the operator again.
• Switch on the operator (correct connection necessary).
•

Important:

Putting into operation in Impulse mode (standard setting) and not in dead man mode.

• During initial operation the choice of language is made first, then in the “Basic settings” the adjustment of most impor

tant operator settings and after the system test, the automatic detection of limit positions of gate is made.

Note: during operation with the basic setting for limit positions OPEN/CLOSE (=-5), the limit stops will not be reached

(only with adjustment = 0)

LANGUAGE SELECTION

•

Can be selected during initial operation (hence after reset to factory settings).

•

Can be also chosen by pressing the ESC button

(ESC)

for 5s, from any position in menu.

BASIC SETTINGS

•

For setting the most important adjustments for initial operation of motor.

•

Can be selected during initial operation (hence when restoring the factory setting).

•

All safety devices are activated when leaving factory

(see menu page 17).

•

The next programming adjustments are made in the main settings menu

(see page 16, 17).

$$$$$$$$$$$$$$$$

photocell

$$$$$$$$$$$$$$$$

photocell

active

$$$$$$$$$$$$$$$$

photocell

not active

change ? YES

confirm

PHC

$$$$$$$$$$$$$$$$

Sprache-language

Deutsch

$$$$$$$$$$$$$$$$

Tousek Vx.x

TPS20

$$$$$$$$$$$$$$$$

basic settings

scroll

confirm

confirmation

$$$$$$$$$$$$$$$$

Sprache-language

English

Содержание TPS 20

















































Результаты поиска

Содержание TPS 20

Отзывы:

Похожие инструкции для TPS 20

Бренды по названию

Популярные бренды

tousek TPS 20, Руководство по монтажу и установке

Результаты поиска

Содержание TPS 20

Отзывы:

Похожие инструкции для TPS 20

Бренды по названию

Популярные бренды