tousek TPS 20 Скачать руководство пользователя | Manualshive

Страница: 19 / 48

background image

tousek

/ E_TPS-20_03 / 30. 08. 2016

- 19 -

Emergency mode

Buttons / switches



not active



active:

In case of malfunction of the safety devices, the gate can be opened with reduced speed in DEAD MAN mode

by means of the impulse button, and it can be closed by means of the CLOSE button. By pressing the respective

button for 5s, you enter the emergency mode. The door will keep moving as long as the button well be pressed.

In traffic light mode or if the impulse button is set to „DEAD-MAN“ the the emergency mode is

not active.

•

As pedestrian button you can use pushbuttons or key switches as well as external radio receivers with

potential free make contacts can be used.

In traffic light mode the pedestrian button is without function

.

Pedestrian button

(terminals 30/34)

Buttons / switches



OPEN/ STOP / CLOSE impulse repetition:

After a command of the pedestrian opening button the
motor for pedestrian opening starts with an open- or
closing movement. If the button is pressed again during
this movement, the motor stops. With the next command
the motor drives in the opposite direction of the last gate
movement.



OPEN / CLOSE / OPEN impulse repetition:

after a

command of the pedestrian opening button the motor
starts an open or close movement. If the button is pressed
again during this movement, the motor reverses.



OPEN:

Only open commands are accepted of the pedestrian opening button. Closing the pedestrian entry with the

button is not possible.



DEADMAN:

The motor opens as long as the pedestrian button is pressed – closing the gate

with the pedestrian button is not possible. As soon as the switch is released, the gate stops.

As soon as DEADMAN is selected, the radio receiver is without function for safety reasons.

pedestrian opening button
(e.g. key switch EPZ 1-1T)

•

In this operation mode it is not possible to stop the motor with the pedestrian button – it always

travels until reaching an end position. (Opened or closed position).

• for the function OPEN/CLOSE/OPEN we strongly suggest the installation of a photocell!

The DEAD MAN setting cannot be actively selected, but it gets automatically selected when the impulse

button is set on DEAD MAN.

P 1

34
30

STOP-switch

(terminals 30/31)

Buttons / switches

•

when pressing the stop switch the gate stops in any

desired position.

Important

If no stop switch is connected, terminals
30/31 have to be wire-bridged.

As stop switch a break contact has to be used.

31
30

STOP-button
(e.g. switch KDT-1N)

31
30

CLOSE-button

(terminals 30/33)

Buttons / switches

•

A command with the CLOSE-switch engages clo-

sing of gate. In deadman mode the gate closes as
long as the CLOSE-switch is pressed/switched.
As soon as switch is released the gate movement stops.

As CLOSE-buttons you may use pushbuttons or
key switches as well as external radio receivers
with potential free make contacts can be used.

In traffic light mode the CLOSE button

is without function

.

CLOSE-button
(e.g. key switch EPZ 1-2T)

2 P 1

33
30

«
...
17
18
19
20
21
...
»

Содержание TPS 20

















































Отзывы:

Нет отзывов

Похожие инструкции для TPS 20

Бренд: CAME Страницы: 108

Бренд: Wayne-Dalton Страницы: 18

Бренд: DTS Страницы: 19

Automatic Technology Battery Backup Gen 2...

Бренд: B&D Страницы: 8

Бренд: West Bend Страницы: 20

Бренд: Nice Страницы: 148

Бренд: fadini Страницы: 13

Бренд: Key Automation Страницы: 76

Бренд: Chamberlain Страницы: 41

Security+ 4200DI

Бренд: Doit Страницы: 40

Бренд: Wayne-Dalton Страницы: 24

Бренд: Wayne-Dalton Страницы: 59

Бренд: Power Drive Страницы: 40

Бренд: SOMFY Страницы: 24

Бренд: BelFox Страницы: 288

Бренд: Chamberlain Страницы: 88

Бренд: Roger Technology Страницы: 8

Бренд: Chamberlain Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды