tousek TPS 20 Скачать руководство пользователя страница 13

Страница: 13 / 48

tousek

/ E_TPS-20_03 / 30. 08. 2016

- 13 -

Warning notes

•

Before taking off the control cover, the

main switch must be turned off!

•

If the control is power supplied, its inner part is under
tension.

•

In order to avoid electrical strokes, the safety regula-
tions have to be kept.

•

The device may only be connected by trained profes-
sionals.

•

The product is not suitable for installation in explosion-
hazardous areas.

•

An all-pole disconnecting main switch with a contact

opening gap of min. 3 mm has to be foreseen. The
gate facility has to be secured according to the valid

safety regulations!

•

IMPORTANT: The control lines (buttons, radio, pho

tocells, etc.) have to be laid separately from the 230V

lines (supply line, motors, signal lamp).

p r e - w i r e d

3.1 Terminal assignment TPS 20, TPS 20N

Sliding gate operator TPS 20, -20N

• During connection, adjustment and maintenance works please take care, that the electronic circuit

board won´t be damaged by moisture (rain).

Grounding

Power supply

230V a.c.

Signal lamp 230V

max. 40W

0 1

10 11

30 31 32 30 33 30 34

fic

lig

(optional)

power supply

ell

smi

tte

r s

ply

ll r

eiv

and accessories, max. 0,3A

mmo

ell

t (

bus system

control unit

traffic light

Low

High

88 89

transmitter

ive

88 89 41 42 43 44 45 46 48

Notentriegelung

Common

Main safety sensing edge

Common

Side safety s. edge 1 OPEN

Common

Side safety s. edge 2 CLOSE

Common

Side safety s. edge 3 OPEN

bro

blue

gray

bla

green/yellow

28 29

20 21 22

23 8 9

.c.

Motor 230V a.c.

Grounding

additional condenser

common

swi

tch

swi

tch

common

swi

tch

common

str

ian

swi

tch

Function main safety sensing edge

(MCE):

Safety during closing

Function side safety sensing edges

(SE):

Safety during opening: SE1, SE3
Safety during closing: SE2

MCE

SE2

SE3

SE1

CLOSE OPEN

58 59

50 51 50 52 50 55 50 56

If no stop switch is connected, ter-
minals 30/31 have to be wire-bridged
(the jumper is set in the factory).

Содержание TPS 20

















































Результаты поиска

Содержание TPS 20

Отзывы:

tousek TPS 20, Руководство по монтажу и установке, Страница: 13 / 48

Результаты поиска

Содержание TPS 20

Отзывы: