tousek TPS 20 Скачать руководство пользователя страница 33

Страница: 33 / 48

tousek

/ E_TPS-20_03 / 30. 08. 2016

- 33 -

CLICK

$$$$$$$$$$$$$$$$

system test

photocell

$$$$$$$$$$$$$$$$

system test

PHC back area

$$$$$$$$$$$$$$$$

system test

Main clos. edge

$$$$$$$$$$$$$$$$

limit positions

being detected

$$$$$$$$$$$$$$$$

Open position

being detected

$$$$$$$$$$$$$$$$

Close position

being detected

$$$$$$$$$$$$$$$$

Ready

$$$$$$$$$$$$$$$$

system test

Side edge1 OPEN

$$$$$$$$$$$$$$$$

system test

Side edge2 CLOSE

$$$$$$$$$$$$$$$$

system test

Side edge3 OPEN

In case of a power failure or other defect the drive pinion
can be disengaged from the gearmotor as follows:

• Switch off power supply !

• Turn the lock cover (A) in counter-clockwise direction,

until the emergency release key can be inserted.

Now turn the key (S) to the left and up to the stop (anti-

clockwise), until you hear a click and it reaches the
unlocked position.

• Now the gate can be opened and closed by hand.

Re-engaging the emergency release mechanism:

To return to normal motor operation please turn back

the key to its original position.

Important

•

After the key has been turned back, slowly move

the gate manually in its travel direction until you

can hear that the gearing has re-engaged!

Remove the key afterwards.

With next command the motor searches the open position (a
new learning of end positions is not necessary).

Emergency release in case of power failure

(note for the user)

TPS 20, -20N, -20PRO

Содержание TPS 20

















































Результаты поиска

Содержание TPS 20

Отзывы:

tousek TPS 20, Руководство по монтажу и установке, Страница: 33 / 48

Результаты поиска

Содержание TPS 20

Отзывы: