tousek TPS 20 Скачать руководство пользователя

Страница: 14 / 48

- 14 -

tousek

/ E_TPS-20_03 / 30. 08. 2016

Elements of control box

(ST)

Control board

(see p. 12)

(FE)

Socket for radio receiver

(see p. 29)

(ISD)

Socket for induction loop detector

(see p. 29)

(REL)

Decoupling relay

(H)

Main switch

(SD)

230V Schuko socket

(X1)

Terminal block

3.2 Control box TPS 20 PRO

Sliding gate operator TPS 20 PRO

Overview of the control box

ISD

REL

Unlike the operators TPS 20, -20N the TPS 20

PRO has an additional terminal block X1. All

connections have to be done at this block,
which is internally connected with the control
board ST.

Warning notes

•

Before opening the control box, the

main switch must be turned off!

•

If the control is power supplied, its inner part is under
tension.

•

In order to avoid electrical strokes, the safety regula-
tions have to be kept.

•

The device may only be connected by trained profes-
sionals.

•

The product is not suitable for installation in explosion-
hazardous areas.

•

An all-pole disconnecting main switch with a contact

opening gap of min. 3 mm has to be foreseen. The
gate facility has to be secured according to the valid

safety regulations!

•

IMPORTANT: The control lines (buttons, radio, pho

tocells, etc.) have to be laid separately from the 230V

lines (supply line, motors, signal lamp).

Содержание TPS 20

















































Результаты поиска

Содержание TPS 20

Отзывы:

Похожие инструкции для TPS 20

Бренды по названию

Популярные бренды

tousek TPS 20, Руководство по монтажу и установке

Результаты поиска

Содержание TPS 20

Отзывы:

Похожие инструкции для TPS 20

Бренды по названию

Популярные бренды