tousek TPS 20 Скачать руководство пользователя страница 18

Страница: 18 / 48

- 18 -

tousek

/ E_TPS-20_03 / 30. 08. 2016

As impulse emitters pushbuttons or key switches as well as external radio receivers with potential free make
contacts can be used.

• A general status display of all inputs can be found in the menu DIAGNOSIS / STATUS DISPLAY

Buttons / switches

Connections and adjustments

Impulse button

(terminals 30/32)

Buttons/switches



OPEN/ STOP / CLOSE impulse repetition

(factory

settings): After a command of the impulse switch the
motor starts an open or close movement. If the impulse
switch is pressed again during this movement, the motor
stops. With the next command, the motor drives in the
opposite direction of the last gate movement.



OPEN / CLOSE / OPEN impulse repetition:

After a command of the impulse switch the motor starts an open or

close movement. If the impulse switch is pressed again during this movement, the motor reverses.

•

In this operation mode it is not possible to stop the motor with the impulse switch – it always

travels until reaching an end position. (Opened or closed position).

• for the function OPEN/CLOSE/OPEN we strongly suggest the installation of a photocell!



OPEN:

Only open commands are accepted of the impulse switch. Closing the gate with the impulse switch is not

possible.

In traffic light mode automatically the adjustment „OPEN“ is active.



DEAD-MAN:

The motor opens as long as the impulse switch is pressed – closing the gate with the impulse switch is

not possible. As soon as the switch is released, the gate stops. If hold to run operating mode is selected,

the radio

receiver is set out of order for reasons of safety.

IMPORTANT: Do not put into operation in dead man mode.

Select only after putting into operation (see page 31), if desired.

Impulse switch
(e.g key switch EPZ 1-2T)

3.5 Connections and adjustments

Sliding gate operator TPS 20, -20N, -20PRO

Warning

•

Before taking off the control cover, the

main switch must be turned off!

•

If the control is power supplied, its inner part is under
tension.

•

In order to avoid electrical strokes, the safety regula-
tions have to be kept.

•

The device may only be connected by trained profes-
sionals.

•

The product is not suitable for installation in explosion-
hazardous areas.

•

An all-pole disconnecting main switch with a contact

opening gap of min. 3 mm has to be foreseen. The
gate facility has to be secured according to the valid

safety regulations!

•

IMPORTANT: The control lines (buttons, radio, pho

tocells, etc.) have to be laid separately from the 230V

lines (supply line, motors, signal lamp).

2 P 1

30
32

The different menu points are indicated as follows:



= selectable setting



= factory settings



= status display

shows the menu points which are in the “ BASIC SETTINGS”

Pedestrian function

(terminals: 30/34)

Buttons/switches



Partial opening

: The contact at terminals 30/34 will be used as pedestrian button.



Impulse OPEN:

The contact at terminals 30/34 works as a second impulse button with the fixed adjustment „OPEN“.

Содержание TPS 20

















































Результаты поиска

Содержание TPS 20

Отзывы:

tousek TPS 20, Руководство по монтажу и установке, Страница: 18 / 48

Результаты поиска

Содержание TPS 20

Отзывы: