tousek TPS 20 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 48

tousek TPS 20 Скачать руководство пользователя страница 30

- 30 -

tousek

/ E_TPS-20_03 / 30. 08. 2016

Important

•

With the use of the 2-channel-receiver the second
channel takes over the function of the pedestrian
entry mode switch.

With the RS 433 version a connecting cable from

the terminals of the receiver board to the pedestrian
button input of the control unit is required.

• For programming of receiver please

see manual for

radio receiver.

Important notes after installation

• Installation, connection, adjustments, putting into operation, and servicing may only be carried out by trained professionals in full

accordance with these installation- and operating instructions.

• The packaging materials (cardboard, plastic, EPS foam parts and filling material etc.) have to be properly disposed of in accordance

with the applying recycling and environmental protection laws. They may be hazardous to children and therefore have to be stored
out of children´s reach.

• The product is not suitable for installation in explosion-hazardous areas.
• The product may only be used in accordance with its original purpose, for which it has been exclusively designed, and which is

described in these installation and operating instructions (especially children have to be instructed). The TOUSEK Ges.m.b.H. rejects
any liability if the product is used in any way not fully conforming to its original purpose as stated herein.

• All electrical installations have to be made in full conformity with the applying rules and laws (e.g. using a fault current circuit breaker,

proper grounding etc.).

•  An all-pole disconnecting main switch with a contact opening-gap of minimum 3 mm has to be foreseen.
•  The electric motor heats up during operation. Therefore the device should only be touched after it has cooled off.
•  After installation the proper function of the gate facility and the safety devices has to be checked!
•  The installer has to inform the user about all aspects of the automatic operation of the complete gate facility, as well as about emer

-

gency operation. The installer further has to supply to the user all instructions relating to the safe operation of the gate facility.
The installation and operating instructions also have to be handed over to the user.

FE

E

FE

• Turn off power supply.

•

Plug-in the receiver printed circuit board

(E)

RS433/868-

STN1 (1-channel) or RS433/868-STN2 (2-channels) into
the corresponding slot

(FE)

as shown in the picture.

• To increase the range an external antenna FK433 or FK868

can be connected.

5.

Connecting the receiver

(optional)

at TPS 20, -20N

Sliding gate operator TPS 20, -20N

«
...
28
29
30
31
32
...
»

Содержание TPS 20

















































Отзывы:

Нет отзывов