manualshive.com logo in svg

Toshiba MMC-AP0151H, Руководство по обслуживанию

Toshiba MMC-AP0151H - качественный кондиционер с инновационными технологиями. На manualshive.com вы можете бесплатно скачать сервисный мануал и руководство пользователя для этой модели. Подробная информация о продукте поможет вам узнать все особенности и настроить в соответствии с вашими потребностями.

Поделиться
Скачать
background image

141

Check code

Main

remote

controller

H08

H14

H16

Outdoor 7-segment display

Check code

Sub-code

H08

01: TK1 sensor error
02: TK2 sensor error
03: TK3 sensor error
04: TK4 sensor error

H14

—

H16

01: TK1 oil circuit

system error

02: TK2 oil circuit

system error

03: TK3 oil circuit

system error

04: TK4 oil circuit

system error

AI-NET

central control

remote controller

d4

44

d7

Detected
position

I/F

I/F

I/F

Check code name

Oil level detective
temp sensor error

Compressor 2
case thermo
operation

Oil level detective
circuit system
error
MG-SW error
OCR operation

Status

All stop

All stop

All stop

All stop

All stop

All stop

Error detection condition

• Resistance value of

sensor is infinite or zero.
(Open/Short)

• Resistance value of

sensor is infinite or zero.
(Open/Short)

• Resistance value of

sensor is infinite or zero.
(Open/Short)

• Resistance value of

sensor is infinite or zero.
(Open/Short)

Compressor 2 case
thermostat operated.

Temperature change of
TK1 could not be detected
though compressor 1
started the operation.

Temperature change of
TK2 could not be detected
though compressor 2
started the operation.

Temperature change of
TK3 could not be detected
though compressor
started the operation.

Temperature change of
TK4 could not be detected
though compressor
started the operation, or
the difference from other
TK sensor changed for a
constant time only within
the specified range.

Check item (position)

• Check connection of TK1 sensor connector.
• Check characteristics of TK1 sensor resistance value.
• Check outdoor P.C. board (I/F) error.

• Check connection of TK2 sensor connector.
• Check characteristics of TK2 sensor resistance value.
• Check outdoor P.C. board (I/F) error.

• Check connection of TK3 sensor connector.
• Check characteristics of TK3 sensor resistance value.
• Check outdoor P.C. board (I/F) error.

• Check connection of TK4 sensor connector.
• Check characteristics of TK4 sensor resistance value.
• Check outdoor P.C. board (I/F) error.

• Check compressor 2 case thermo circuit. (Connector, cable, P.C. board)
• Check full opening of service valve. (Gas and liquid side)
• Check outdoor PMV clogging. (PMV1, 2)
• Check SV42 valve leak.
• Check miscabling/misinstallation of SV41 and SV42.
• Check valve opening of indoor PMV.
• Check 4-way valve error.
• Check refrigerant shortage.
• Check compressor error.

• Check TK1 sensor coming-off.
• Check characteristics of TK1 sensor resistance value.
• Check TK1, TK2, TK3, and TK4 misconnection.
• Check operation error of SV3E valve.
• Check capillary clogging of oil-equation circuit and operation error of stop valve.
• Check refrigerant stagnation in compressor.
• Check MG-SW or OCR.

• Check TK2 sensor coming-off.
• Check characteristics of TK2 sensor resistance value.
• Check TK1, TK2, TK3, and TK4 misconnection.
• Check SV3E valve operation.
• Check capillary clogging of oil equalization circuit and check stop valve operation.
• Check refrigerant stagnation in compressor shell.
• Check MG-SW or OCR.

• Check TK3 sensor coming-off.
• Check characteristics of TK3 sensor resistance value.
• Check TK1, TK2, TK3, and TK4 misconnection.
• Check SV3E valve operation.
• Check capillary clogging of oil-equalization circuit and check valve operation.
• Check refrigerant stagnation in compressor shell.
• Check MG-SW or OCR.

• Check TK4 sensor coming-off.
• Check characteristics of TK4 sensor resistance value.
• Check TK1, TK2, TK3, and TK4 misconnection.
• Check SV3E valve operation.
• Check capillary clogging of oil-equalization circuit and check valve operation.
• Check refrigerant stagnation in compressor shell.
• Check MG-SW or OCR.

MG-SW : Magnet Switch

OCR

: Over-current Relay

Содержание MMC-AP0151H















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MMC-AP0151H

Jaga Briza 22 Quick Start Manual preview
Briza 22
Бренд: Jaga Страницы: 12
Quasar HQ2200PH Installation And Operating Insctructions preview
HQ2200PH
Бренд: Quasar Страницы: 24
Quasar HQ2061QH Install And Operation Instructions preview
HQ2061QH
Бренд: Quasar Страницы: 24
Quasar HQ2050PH Installation And Operaing Instructions preview
HQ2050PH
Бренд: Quasar Страницы: 20
Haier IKI-09 User Manual preview
IKI-09
Бренд: Haier Страницы: 28
Daikin Super Multi NX FTXG25JV1BW Installation Manual preview
Super Multi NX FTXG25JV1BW
Бренд: Daikin Страницы: 26
Daikin SUPER MULTI NX CTXS07JVJU Operation Manual preview
SUPER MULTI NX CTXS07JVJU
Бренд: Daikin Страницы: 34
Daikin Super Multi NX ATXS20G2V1B Operation Manual preview
Super Multi NX ATXS20G2V1B
Бренд: Daikin Страницы: 34
Daikin VRV FXTQ12PVJU Operation Manual preview
VRV FXTQ12PVJU
Бренд: Daikin Страницы: 6
Daikin VRV II Series Technical Data Manual preview
VRV II Series
Бренд: Daikin Страницы: 22
Daikin VRV FXDQ15P2VE Operation Manual preview
VRV FXDQ15P2VE
Бренд: Daikin Страницы: 8
Daikin Super Multi NX FTXS20J2V1B Operation Manual preview
Super Multi NX FTXS20J2V1B
Бренд: Daikin Страницы: 46
Daikin Super Multi NX FTXS20G2V1B Operation Manual preview
Super Multi NX FTXS20G2V1B
Бренд: Daikin Страницы: 38
Daikin FT25CV1A Operation Manual preview
FT25CV1A
Бренд: Daikin Страницы: 24
Daikin Super Multi NX FTXS60GV1B Operation Manual preview
Super Multi NX FTXS60GV1B
Бренд: Daikin Страницы: 44
Daikin SUPER MULTI NX FDXS09DVJU Operation Manual preview
SUPER MULTI NX FDXS09DVJU
Бренд: Daikin Страницы: 26
Danby DAP290BAW Owner'S Manual preview
DAP290BAW
Бренд: Danby Страницы: 28
Daikin FTX09AXVJU Operating Manual preview
FTX09AXVJU
Бренд: Daikin Страницы: 88

Бренды по названию

Популярные бренды

Загрузить еще бренды