Toshiba MMC-AP0151H Скачать руководство пользователя страница 245

Страница: 245 / 270

245

[In case of replacing of both troubled and normal compressors]

<Removal of normal compressor>

• Remove the normal compressor same as the case to remove the troubled compressor.

(NOTE)

• Be sure to apply insulation to the removed cable terminals with insulating tape, etc.

WARNING

Be careful that oil in the pipe may emit fire when broiling the welded point with a burner.

<Measurement of oil amount in the normal compressor>

• As same as measurement of oil amount in the troubled compressor, put the compressor on a scale and

measure oil amount.

Oil amount of the normal compressor: B [cc] = (Removed compressor mass (kg) –23.5) × 1042

(Specific gravity of oil: 1042 [cc/kg])

(NOTE)

• When the compressor holds no oil, the compressor mass is 23.5kg.

<Adjustment of oil amount in the service compressor>

• Adjust oil amount by the contents below:

Based on oil amount of troubled compressor: A[cc] and oil amount of normal compressor: B [cc]

1. In case of the total oil amount of the compressors: A + B [cc] is 0 < A + B < 2000

1) Adjust oil amount in the two service compressors to 1000cc each. (Total: 2000cc)

• Lay down the two service compressors, and then extract oil by 900 [cc] from each oil-equalization pipe.

(NOTE)

• Do not extract oil over 900 [cc] because a trouble may be caused on the compressor.

• If oil amount of the troubled compressor is below 500cc, a trouble on the oil-equalization circuit, etc is

considered. Check the compressor based upon “15-3. Check procedure search the cause of com-
pressor oil shortage”.

2. In case of total oil amount: A + B [cc] is 2000 < A + B < 3800

1) Adjust oil amount in the two service compressors to A + B [cc] each.

• Lay down the two service compressors and then extract oil by

3800 – (A + B) [cc] from each oil-equalization pipe.
2

3. In case of total oil amount of the compressors: A + B [cc] is 3800 < A

1) Adjust oil amount in the two service compressors to A + B [cc] each.

(Insert a hose into the discharge pipe or oil-equalization pipe of the
service compressor, and then add oil by



A + B – 1900



[cc] using a funnel or so on.)





Compressor

Содержание MMC-AP0151H















































































































































































































































































Результаты поиска

Содержание MMC-AP0151H

Отзывы:

Похожие инструкции для MMC-AP0151H

Бренды по названию

Популярные бренды

Toshiba MMC-AP0151H, Руководство по обслуживанию

Результаты поиска

Содержание MMC-AP0151H

Отзывы:

Похожие инструкции для MMC-AP0151H

Бренды по названию

Популярные бренды