Toshiba MMC-AP0151H Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 270

background image

101

Clearance of address

(Return to status (Address undecided) at shipment from factory)

Method 1

An address is individually cleared from a wired remote controller.

“0099” is set up to line address, indoor address, and group address data from the remote controller.

(For the setup procedure, refer to the abovementioned address setup from the remote controller.)

Method 2

Clear the indoor addresses in the same refrigerant line from the outdoor unit.

1. Turn off the power of the refrigerant line to be returned to the status at shipment, and change the header unit

to the following status.

1) Remove the relay connector between [U1U2] and [U3U4].

(If it has been already removed, leave it as it is.)

2) Turn on SW30-2 on the interface P.C. board of the header unit if it is ON.

(If it has been already ON, leave it as it is.)

3. After “A.d. c.L.” has been displayed on 7-degment display, return SW01/SW02/SW03 to 1/1/1.

4. When the address clearing has correctly finished, “U.1.L08” is displayed on 7-degment display after a while.

If “A.d. n.G.” is displayed on 7-degment display, there is a possibility which is connected with the other
refrigerant line. Check again the relay connector between [U1U2] and [U3U4] terminals.

NOTE) Be careful that the other refrigerant line address may be also cleared if clearing operation is not

correctly executed.

5. After clearing of the address, set up an address again.

SW01

SW02

SW03

2

1

2

2

2

2

SW04

After checking that “A.d.buS” is displayed on 7-degment
display, and then push SW04 for 5 seconds or more.

After checking that “A.d.nEt” is displayed on 7-degment
display, and then push SW04 for 5 seconds or more.

Address which can be cleared

Line + Group address

Central address

2. Turn on the indoor/outdoor power of which address is to be cleared. After approx. 1 minute, check that

“U.1. - - -” is displayed, and then execute the following operation on the interface P.C. board of the header unit
of which address is to be cleared in the refrigerant line.

U3 U4

U1 U2

U5 U6

U1 U2

A B

Header unit

Remote

controller

U3 U4

U1 U2

U5 U6

U1 U2

A B

Follower unit

Remote

controller

U3 U4

U1 U2

U5 U6

U1 U2

A B

Remote

controller

U3 U4

U1 U2

U5 U6

U1 U2

A B

Follower unit

U3 U4

U1 U2

U1
U3

U2
U4

U5 U6

U1 U2

A B

Remote

controller

Center unit

Center unit

Center unit

Center unit

Header unit

Header unit

Central control

device

Unit of which address is to be returned to the initial status

«
...
99
100
101
102
103
...
»

Содержание MMC-AP0151H















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MMC-AP0151H

Бренд: BAC Страницы: 28

Бренд: S&S Cycle Страницы: 8

Бренд: Haier Страницы: 28

Duct Type Series

Бренд: Samsung Страницы: 40

Бренд: GE Страницы: 2

CSF_HW_TUBE_R_R

Бренд: Siga Страницы: 14

Бренд: Tecnoclima Страницы: 40

EML2M14S912IST3W

Бренд: Emelson Страницы: 88

Бренд: Seifert Страницы: 21

Бренд: mabe Страницы: 12

Бренд: acerpure Страницы: 40

Бренд: Fedders Страницы: 16

Бренд: HEIL Страницы: 10

Бренд: Hyundai Страницы: 40

Бренд: Crosley Страницы: 4

Бренд: Maytag Страницы: 8

Бренд: REMKO Страницы: 16

Бренд: Daikin Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды