Toshiba MMC-AP0151H, Руководство по обслуживанию

Страница: 95 / 270

95
REQUIREMENT
• When a group control is performed over the
multiple refrigerant lines, be sure to turn on the
power supplies of all the indoor units connected
in a group in the time of address setup.
• If turning on the power for each refrigerant line
to set up address, a header indoor unit is set for
each line. Therefore, an alarm code “L03”
(Duplicated indoor header units) is output in
operation after address setup. In this case,
change the group address from the wired
remote controller for only one header unit is set
up.
(Example)
Cabling
systematic
diagram
Group control over
multiple refrigerant lines
Address setup procedure 2
1. Using SW13 and 14 on the interface P.C. board of
the header unit in each system, set up the system
address for each system.
(At shipment from factory: Set to Address 1)
Note) Be careful not to duplicate with other refriger-
ant line.
System address switch on outdoor interface P.C. board
(
¡
: Switch ON,
×
: Switch OFF)
2. Check that the relay connectors between [U1U2] and
[U3U4] terminals are come out in all the header units to
which the central control is connected.
(At shipment from factory: No connection of connector)
3. Turn on power of indoor/outdoor.
(In order of indoor
→ →
→ → →
outdoor)
4. After approx. 1 minute, check that 7-segment display is
U.1.L08 (U.1. flash) on the interface P.C. board of the
header unit.
5. Push SW15 and start setup the automatic address.
(Max. 10 minutes for 1 line (Usually, approx. 5 minutes))
6. When the count Auto 1
→ → → → →
Auto 2
→ → → → →
Auto 3 is displayed
in 7-segment display section, and it changes from
U. 1. - - - (U. 1. flash) to U. 1. - - - (U. 1. light) , the
setup finished.
7. Procedure 4. to 6. are repeated in other refrigerant lines.
: Is not used for setup of system address. (Do not change setup.)
System
address
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SW13 SW14
1 2 3 4 1 2 3 4
× × × × ×
× ¡ × × ×
× ×
¡
× ×
× ¡ ¡ × ×
× × ×
¡
×
×
¡
×
¡
×
× × ¡ ¡ ×
×
¡ ¡ ¡
×
× × × × ¡
×
¡
× ×
¡
× ×
¡
×
¡
×
¡ ¡
×
¡
× × ×
¡ ¡
× ¡ × ¡ ¡
System
address
15
16
17
18
19
20
21
22
23
24
25
26
27
28
SW13 SW14
1 2 3 4 1 2 3 4
× ×
¡ ¡ ¡
× ¡ ¡ ¡ ¡
¡
× × × ×
¡ ¡ × × ×
¡
×
¡
× ×
¡ ¡ ¡
× ×
¡ × × ¡ ×
¡ ¡
×
¡
×
¡ × ¡ ¡ ×
¡ ¡ ¡ ¡
×
¡
× × ×
¡
¡ ¡
× ×
¡
¡
×
¡
×
¡
¡ ¡ ¡ × ¡
Outdoor
Indoor Indoor
Remote
controller
Outdoor
Indoor Indoor
SW11
1
ON
Header unit interface P.C. board
2 3 4
SW12
1
ON
2 3 4
SW06
1
ON
2 3 4
SW07
1
ON ON ON ON
2 3 4
SW09 SW08
1 1 2 3 4
SW10
1 2 3 4
SW13
1
ON
2 3 4
SW14
1
ON
2 3 4
U1 U2
For internal
wiring between
indoor and
outdoor
U3 U4
For wiring of
central control
system
U5 U6
For internal
wiring between
outdoor units
2