manualshive.com logo in svg

Toshiba MMC-AP0151H, Руководство по обслуживанию

Toshiba MMC-AP0151H - качественный кондиционер с инновационными технологиями. На manualshive.com вы можете бесплатно скачать сервисный мануал и руководство пользователя для этой модели. Подробная информация о продукте поможет вам узнать все особенности и настроить в соответствии с вашими потребностями.

Поделиться
Скачать
background image

71

No.

8

Operation explanation and applied data, etc.

(1) SV2 gas balance control

This control is executed to balance the gas when opening
SV2 while the compressor is off, in order to decrease the
activation load in the next compressor-ON time. This control is
individually executed by the header outdoor unit and each
follower outdoor unit.

(2) SV2 high pressure release control

This control is to control pressure rising in low-frequency
operation of the inverter.

(3) SV2 low pressure release control

This control is to prevent quick pressure dropping in transient
operation. This control is individually executed by the header
outdoor unit.
This control is executed as necessary except during stop time
and thermostat-OFF time.

(4) SV41, 42 low pressure release control

This control is to prevent low pressure dropping and is
individually executed by the header unit and each follower unit.
This control is executed during defrost operation, heating
start pattern control operation, and cooling operation.

(5) SV5 high pressure release control

This control is to prevent high pressure rising and is executed
for the header unit only.

Item

Release valve
control

9

Compressor
stop by high
pressure
release control

This control is to forcedly stop the compressor in each outdoor
unit according to Pd pressure. It is individually executed by the
header unit and each follower unit.
(1) Contents of control

• The compressor stops when Pd pressure is over 3.5MPa.

Remarks

10

Case heater
control

The case heater output includes compressor case heater and
accumulator case heater. This control is to prevent accumulation
of refrigerant in the compressor case by turning of the power of
heater while the compressor stops, and it is executed in all the
outdoor units.
If electricity is not turned on for a specified time before the test
run after installation, a trouble of the compressor may be caused.
When the power has been interrupted for a long time and the
operation starts from the status as it was, it is desirable to turn on
the power before start of operation as per the test run time.
This control is used often together with the compressor winding
heating control. In this case, the power sound may be heard but it
is not a trouble.
(1) Contents of control

• Turns on during compressor-OFF
• Turns off when the detected TO sensor temp is 28°C or

higher, and turns on when it is 25°C or lower

• The operation continues for 10 minutes after compressor-

OFF changed to compressor-ON.

11

IPDU control

IPDU controls the inverter compressor by command frequency,
frequency up/down speed, and current release control value from
the interface P.C. board.
The main controls of IPDU control P.C. board are described
below.
(1) Current release control

The output frequency is controlled by AC input current value
which is detected by inputting current sensor (CT) on the
control P.C. board to prevent the inverter input current from
rising higher than the specified value.

Содержание MMC-AP0151H















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MMC-AP0151H

Fedders Room Air Conditioners Important Safety Instructions Manual preview
Room Air Conditioners
Бренд: Fedders Страницы: 12
AAF AV Operation And Maintenance preview
AV
Бренд: AAF Страницы: 4
Gree CA145006400 Service Manual preview
CA145006400
Бренд: Gree Страницы: 73
Midea MRBT-062CWN1-D Manual preview
MRBT-062CWN1-D
Бренд: Midea Страницы: 84
Black + Decker BPT05WTB Instruction Manual preview
BPT05WTB
Бренд: Black + Decker Страницы: 84
Danby DAC080B6IWDB-6 Owner'S Manual preview
DAC080B6IWDB-6
Бренд: Danby Страницы: 80
Carrier 42XPF Manual preview
42XPF
Бренд: Carrier Страницы: 54
American Comfort ACW800CH Owner'S Manual preview
ACW800CH
Бренд: American Comfort Страницы: 15
Zibro S 3050 Datasheet preview
S 3050
Бренд: Zibro Страницы: 2
F&U PAH-1029 Instruction Manual preview
PAH-1029
Бренд: F&U Страницы: 15
Trotec PAC FT 2600 Safety Instructions And Operation Manual preview
PAC FT 2600
Бренд: Trotec Страницы: 6
Rabbit Air MinusA2 SPA-780N Quick Start Manual preview
MinusA2 SPA-780N
Бренд: Rabbit Air Страницы: 2
Prem-I-Air EH1614/EU Manual preview
EH1614/EU
Бренд: Prem-I-Air Страницы: 15
Evolar EVO-3008CH Manual preview
EVO-3008CH
Бренд: Evolar Страницы: 49
Danby DPA060B1WDB-RF Owner'S Manual preview
DPA060B1WDB-RF
Бренд: Danby Страницы: 67
Williamson-Thermoflo 12SRA-HE Owner'S Manual preview
12SRA-HE
Бренд: Williamson-Thermoflo Страницы: 23
Daikin RX20JV1B Installation Manual preview
RX20JV1B
Бренд: Daikin Страницы: 15
Daikin FTKS20D3VMW Service Manual preview
FTKS20D3VMW
Бренд: Daikin Страницы: 355

Бренды по названию

Популярные бренды

Загрузить еще бренды