Toshiba MMC-AP0151H Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 270

background image

135

In case of AI-NET central control remote controller

1. Operation for CHECK display

When pushing the CHECK switch, the indoor unit No. (Network address No.) including the check data is
displayed in the UNIT No. display section, and the check code is displayed in the set up temp. display section.

CHECK switch

Push for 0.5 seconds to display CHECK code.

Push for 3 seconds to reset indoor microprocessor.
(While indoor microprocessor is locked by ALL STOP alarm)

Push for 10 seconds to clear check data.

RESET switch

Push the switch in the hole with pin.
The remote controller resets initialized.
(All data is cleared.)

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

(Example)

Hexadecimal
notation

Decimal notation

<7 segment display>

<Display on CHECK monitor>

<CHECK data>

In No.1 unit, first the interconnection wire (bus communication line) of indoor/outdoor has failed.
Next, the room temp. sensor is defective.
For No.16 unit, the high pressure switch at the inverter unit side operates.

(Example)
There is no check data.

Unit line No. (Network address No.)

Check code detected at first

Check code detected at last

FILTER RESET

49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

1

MONITOR

SET

ZONE

ALL

CENTER
LOCKED

AUX. TYPE

TIMER No.

STANDBY

FILTER

ON

OFF

MODE
FAN ONLY

COOL

DRY

HEAT

AUTO

ON

UNIT

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

FAN

AUTO

HIGH
MED.

LOW

FIX

TEMP.

CHECK

1
2

˚C

LOUVER
MANUAL

LOUVER

FAN

TEMP.

MODE

MONITOR/SET ALL/ZONE

ZONE

UNIT

ON CENTER/LOCKED

CHECK

ZONE SET/ENTER SELECT

OFF

TIMER ON

49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

1

MONITOR

SET

ZONE

ALL

CENTER
LOCKED

AUX. TYPE

TIMER No.

STANDBY

FILTER

ON

OFF

MODE
FAN ONLY

COOL

DRY

HEAT

AUTO

UNIT

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

FAN

AUTO

HIGH
MED.

LOW

FIX

TEMP.

CHECK

1
2

˚C

LOUVER
MANUAL

UNIT

TEMP.

CHECK

2

UNIT

TEMP.

CHECK

1

UNIT

TEMP.

CHECK

1

UNIT

TEMP.

CHECK

2. Reading of CHECK monitor display

«
...
133
134
135
136
137
...
»

Содержание MMC-AP0151H















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MMC-AP0151H

Бренд: Jet Страницы: 11

Бренд: Jet Страницы: 10

Бренд: Kaden Страницы: 16

Бренд: Kaden Страницы: 16

Бренд: Kaden Страницы: 32

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 94

Бренд: Panasonic Страницы: 89

Бренд: Daikin Страницы: 16

Split Type Room Air Conditioner

Бренд: Midea Страницы: 14

40MKCB**F/24AHA4

Бренд: CAC / BDP Страницы: 24

Бренд: Zamil Страницы: 51

Бренд: Silent Night Страницы: 12

Бренд: Uberhaus Страницы: 24

Бренд: HEIL Страницы: 10

Enviro-Therm SCE-AC5100B230V

Бренд: SCE Страницы: 17

Mr.Slim MSZ-A09NA

Бренд: Mitsubishi Страницы: 15

Бренд: Euromatic Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды