Toshiba MMC-AP0151H Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 270

background image

93

8-4. Address Setup

After power-ON, set up the indoor address from the interface P.C. board of the header unit.

(The address setup operation cannot be performed by power-ON only. )

8-4-1. Cautions

1. It requires approx. 5 minutes usually for 1 line to automatically set up address.

However in some cases, it may require maximum 10 minutes.

2. It is unnecessary to operate the air conditioner for address setup.

3. Manual address setup is also available besides automatic setup.

Automatic address: Setup from SW15 on the interface P.C. board of the header unit

Manual address: Setup from the weird remote controller.
(For details, refer to section “8-4-3. Address setup procedure”)

8-4-2. Address Setup and Check Procedure

Procedure

1

2

3

4

5

6

Item

Indoor unit power-ON

Outdoor unit power-ON

7-segment display
check

Address setup start

Display check after
setup

System information
check after setup

Operation and check contents

Turn on power of indoor unit in refrigerant line to which address is set up.

Turn on power of all the outdoor units in refrigerant line to which address is set up.

Check that [L08] is displayed on 7-segment display [B] on the interface P.C. board of the header
unit in the system to which address is set up.

Confirm the corresponding items in “8-4-3 Address setup procedure”, and then set up address
according to the operation procedure.
(Be sure that the setup operation may differ in group control or central control.)
Note) Address cannot be set up if switches are not operated.

• After address setup, [U1] is displayed in 7-segment display section.

• For follower outdoor units, [U2] to [U4] are displayed in 7-segment display [A].

• If an error code is displayed in 7-segment display [B], remove the cause of trouble referring to

“9. Troubleshooting”.

Using 7-segment display function, check the system information of the scheduled system.
(This check is executed on the interface P.C. board of the header unit.)

System capacity

No. of connected outdoor units

No. of connected indoor units

Rotary switch setup

SW01

SW02

SW03

1

2

3

1

3

3

1

4

3

7-segment display

[A]

[B]

[No. of HP]

[HP]

[No. of units]

[ P]

[Connected No. of units]

After the above checks, return rotary switches SW01, SW02, SW03 to 1/1/1.

Interface P.C. board

SW01

SW02

<Rotary switches>

SW03

7-segment
display [A]

Push-switch
SW04

Push-switch
SW05

Push-switch
SW15

7-segment
display [B]

«
...
91
92
93
94
95
...
»

Содержание MMC-AP0151H















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MMC-AP0151H

Бренд: Daikin Страницы: 61

Бренд: Daikin Страницы: 5

Бренд: Daikin Страницы: 23

Бренд: Daikin Страницы: 20

Altherma EABH16DA6V

Бренд: Daikin Страницы: 16

Бренд: QuietFlo Страницы: 24

Бренд: Unitary products group Страницы: 68

Бренд: Haier Страницы: 57

Бренд: Panasonic Страницы: 198

S-15MY2E5A CZ-KPY3A

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 52

Бренд: Daikin Страницы: 32

Бренд: GE Страницы: 40

Бренд: Haier Страницы: 8

VRV FXZQ07MVJU9

Бренд: Daikin Страницы: 27

Comfort 50VL-C 24

Бренд: Carrier Страницы: 6

Бренд: York Страницы: 16

Бренд: Daikin Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды