Toshiba MMC-AP0151H Скачать руководство пользователя страница 246

Страница: 246 / 270

246

<Installation of compressor>

• Install the compressor in the reverse procedure of removal.

• When removing the compressor, Fasten receptacle terminals of the compressor may be loosened.

Prior to the installation, caulk a little to them with radio pinchers, reinsert them into the compressor,
and then check there is no looseness.

(NOTES)

• Only two hexagonal bolts are provided to a compressor, but it is not lacking.

• The tightening torque of the hexagonal bolt to fix the compressor is 200kg/cm.

• If oil has been extracted from the accumulator, braze the cutoff pipe after pinching.

<Vacuuming>

(In case of single outdoor system>

• Connect vacuum pump to the valve charge ports of the liquid and gas pipes and the check joint at high-

pressure side, and then drive the vacuum pump.

• Vacuum until the vacuum low-pressure gauge indicates 1 (mmHg).

(NOTE)

• Before vacuuming, open PMV fully. Vacuuming may not be executed for the heat exchanger of the outdoor

unit under condition of PMV closed.

(In case of multiple outdoor units system)

• In case of conducting the refrigerant recovery at replacing the compressor, perform vacuuming as

13-3. Process after repair.

<Full opening of PMV>

• Turn on power of the outdoor unit.

• Short CN30 on I/F P.C. board of the outdoor unit.

• Turn off power of the outdoor unit within 2 minutes after short-circuiting.

<Refrigerant charging>

• Add the same amount of refrigerant as the remaining refrigerant refrigerant from the charge port of the

service valve at liquid side.

Содержание MMC-AP0151H















































































































































































































































































Результаты поиска

Содержание MMC-AP0151H

Отзывы:

Похожие инструкции для MMC-AP0151H

Бренды по названию

Популярные бренды

Toshiba MMC-AP0151H, Руководство по обслуживанию

Результаты поиска

Содержание MMC-AP0151H

Отзывы:

Похожие инструкции для MMC-AP0151H

Бренды по названию

Популярные бренды