manualshive.com logo in svg

Toshiba MMC-AP0151H, Руководство по обслуживанию

Toshiba MMC-AP0151H - качественный кондиционер с инновационными технологиями. На manualshive.com вы можете бесплатно скачать сервисный мануал и руководство пользователя для этой модели. Подробная информация о продукте поможет вам узнать все особенности и настроить в соответствии с вашими потребностями.

Поделиться
Скачать
background image

144

Check code

Main

remote

controller

P07

P10

P12

P13

P15

P17

P19

Outdoor 7-segment display

Check code

Sub-code

P07

01: Compressor

1 side

02: Compressor

2 side

P10

Indoor address
with trouble

—

—

P13

—

P15

01: TS condition

02: TD condition

P17

—

P19

Detected
outdoor unit No.

AI-NET

central control

remote controller

1C

Ob

11

47

AE

AE

bb

8

Detected
position

IPDU

I/F

Indoor

Indoor

I/F

I/F

I/F

I/F

I/F

Check code

name

Heat sink
overheat error

Indoor overflow
error

Indoor fan
motor error

Outdoor liquid
back detection
error

Gas leak
detection
(TS1 condition)

Gas leak
detection
(TD condition)

Discharge
temp TD2 error

4-way valve
operation error

Status

All stop

All stop

Corresponding
unit only stops.

All stop

All stop

All stop

All stop

All stop

Error detection condition

IGBT built-in temp sensor (TH) was overheated.

• Float switch operated.
• Float switch circuit disconnected or the

connector came off.

• The value of motor speed deviated from

target value was detected for certain time.

• Over-current protection operated.

<In cooling>
While the system is operating in COOL mode, a
high pressure value was detected in follower
unit in which compressor did not operate.
<In heating>
While the system is operating in HEAT mode,
outdoor PMV of which opening degree was
100p or less for a certain time.

Suction temp exceeded the judgment standard
temp for 10 minutes or more.
<TS error judgment standard temperature>
In cooling operation: 60°C or higher
In heating operation: 40°C or higher

Discharge temperature TD1 or TD2 was
continuously 108°C or higher for 10 minutes.

Discharge temperature (TD2) exceeded 115°C.

When abnormal refrigerating cycle data was
detected in heating

Check item (position)

• Check power voltage.
• Check outdoor fan system error.
• Check clogging of heat sink cooling duct.
• Check fixation between IGBT and heat sink.

(Check screwing and contact.)

• Check IPDU error.(IGBT built-in temp sensor (TH) error)

• Check the float switch connector.
• Check operation of drain pump unit.
• Check the drain pump circuit.
• Check clogging of drain pipe.
• Check indoor P.C. board error.

• Check connection of fan connector and wiring.
• Check fan motor error.
• Check indoor P.C. board error.
• Check influence of outside air control.
• Check indoor type code (DN=10) and the capacity code (DN=11).

• Check full close operation of outdoor PMV (1, 2).
• Check Pd and Ps sensor error.
• Check clogging of SV2 circuit.
• Check clogging of balance pipe.
• Check clogging of SV3B circuit.
• Check outdoor P.C. board (I/F) error.
• Check capillary clogging of oil return circuit from oil separator.
• Check leakage of check valve of the main discharge pipe.

• Check refrigerant shortage.
• Check full open of outdoor service valves (gas side, liquid side).
• Check outdoor PMV clogging (PMV1, 2).
• Check characteristics of TS1 sensor resistance value.
• Check 4-way valve error.
• Check leakage of SV4 circuit.

• Check refrigerant shortage.
• Check outdoor PMV clogging (PMV1, 2).
• Check characteristics of TD1, TD2 sensor resistance value.
• Check indoor air filter clogging.
• Check pipe clogging.
• Check SV4 circuit (Valve leakage, misinstallation)

• Check full opening of outdoor service valves

(gas side, liquid side).

• Check clogging of outdoor PMV (PMV1, 2).
• Check characteristics of TD2 sensor resistance value.
• Check 4-way valve error.
• Check leakage of SV42 circuit.
• Check SV4 circuit.

(Miscabling and misinstallation of SV41 and SV42)

• Error of 4-way valve error
• Check coil error and connector connection of 4-way valve.
• Check characteristics of TS1/TE1 sensor resistance value.
• Check characteristics of Pd, Ps pressure sensor output voltage.
• Check misconnection of TE1 and TL sensors.

Содержание MMC-AP0151H















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MMC-AP0151H

Magic-Pak EWC V Series Installation Instructions preview
EWC V Series
Бренд: Magic-Pak Страницы: 5
IconBiT U LIGHT COMBO TRS2075 User Manual preview
U LIGHT COMBO TRS2075
Бренд: IconBiT Страницы: 2
Samsung AM AN4PKH Series Installation Manual preview
AM AN4PKH Series
Бренд: Samsung Страницы: 40
Alfa Network LU-VE Arctigo ISD Instruction Manual preview
LU-VE Arctigo ISD
Бренд: Alfa Network Страницы: 32
Amcor PLMB mono 12KE-410 Instruction Manual preview
PLMB mono 12KE-410
Бренд: Amcor Страницы: 12
Kaysun KMF-80 DVN3 Owner'S Manual preview
KMF-80 DVN3
Бренд: Kaysun Страницы: 12
Daikin FDBQ25B7V1 Operation Manual preview
FDBQ25B7V1
Бренд: Daikin Страницы: 8
EQUATION 3276007041705 Manual preview
3276007041705
Бренд: EQUATION Страницы: 45
TriStar AT-5464 Instruction Manual preview
AT-5464
Бренд: TriStar Страницы: 12
ICP PAF354000K00A1 Installation Instructions Manual preview
PAF354000K00A1
Бренд: ICP Страницы: 13
Pure n Natural Systems PR20.0 User Manual preview
PR20.0
Бренд: Pure n Natural Systems Страницы: 4
Kodak AP550 DUAL FAN User Manual preview
AP550 DUAL FAN
Бренд: Kodak Страницы: 33
Rasonic RC-XN1221V Operating Instructions preview
RC-XN1221V
Бренд: Rasonic Страницы: 2
REMKO RKL 220 Operation Manual preview
RKL 220
Бренд: REMKO Страницы: 16
Sedna Aire CM Multi Split Series Installation Manual And User'S Manual preview
CM Multi Split Series
Бренд: Sedna Aire Страницы: 20
COMFORT-AIRE REG-123M Owner'S Manual preview
REG-123M
Бренд: COMFORT-AIRE Страницы: 20
Carrier CPFILTRK007A00 Installation Instructions preview
CPFILTRK007A00
Бренд: Carrier Страницы: 4
Olimpia splendid Qi INVERTER 10 Instructions For Installation, Use And Maintenance Manual preview
Qi INVERTER 10
Бренд: Olimpia splendid Страницы: 144

Бренды по названию

Популярные бренды

Загрузить еще бренды