Thermo Scientific Dionex Easion Скачать руководство пользователя страница 61

Страница: 61 / 126

4 • Troubleshooting

Doc. 155028-01 08/20

•

Leaking Dionex CRS 500

Refer to the suppressor manual for troubleshooting procedures.

•

Leaking injection valve

1. Make sure the liquid line connections to the valve are tight. Replace any

damaged fittings. Refer to

Installation of Dionex Liquid Line Fittings

(Document No. 031432) for tightening requirements.

2. Liquid leaks from behind the valve stator may indicate a scratched rotor

seal. Rebuild the injection valve (see

Section 5.11

•

Leaking conductivity cell

1. Check the waste lines for blockage; trapped particles can plug the lines

and cause a restriction and/or leak. If necessary, clear the waste lines by
reversing the direction of flow.

2. Make sure the plumbing downstream from the cell is clear; a blockage

may overpressurize the cell, causing it to leak. If the problem continues,
contact Technical Support for Dionex products for assistance.

4.3

Pump Difficult to Prime or Loses Prime

•

Empty eluent bottle and/or no eluent connected

1. Fill the eluent bottle, and then use the

Eluent Fill Volume

slider on the

Chromeleon ePanel to reset the volume of liquid in the bottle.

2. Make sure all connections are secure.

•

Dirty pump check valve

Replace (see

Section 5.6

) or clean (see

Section 5.7

) the check valves.

•

Liquid leaks at junction between pump head and pump housing

Replace the piston seal (see

Section 5.8

4.4

Pump Does Not Start

•

No power (front door

Power

LED indicator fails to light)

1. Check that the power cord is plugged in.

2. Check the main power fuses and replace, if needed (see

Section 5.14

Содержание Dionex Easion































































































































Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды

Thermo Scientific Dionex Easion, Руководство оператора

Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды