Thermo Scientific Dionex Easion Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 126

background image

Dionex Easion Operator’s Manual

12

Doc. 155028-01 08/20

Conductivity Cell

The flow-through heated conductivity cell measures the electrical
conductance of analyte ions as they pass through the cell. A heat
exchanger inside the cell regulates the temperature to 40 °C (104 °F). The

cell is housed inside a Thermo Scientific

™

Dionex

™

DS5 Detection

Stabilizer (P/N 067761). For more information about the conductivity cell
and Dionex DS5 Detection Stabilizer, see

.

Suppressor

The suppressor reduces the eluent conductivity and enhances the
conductivity of the sample ions, thereby increasing detection sensitivity.

The Thermo Scientific

™

Dionex

™

Chemically Regenerated Suppressor

(Dionex CRS

™

500) is recommended for use with the Dionex Easion. For

more information about suppressors, see

.

Separator and Guard Columns

Both the separator and guard columns are packed with resin and perform
the separation of the sample ions. The main function of the guard column
is to trap contaminants and particulates that might damage the separator
column.

Pressure Transducer

The pressure transducer measures the system backpressure. For more
information about the pressure transducer, see

Pump Heads

The Dionex Easion includes a dual-piston serial pump. The flow rate can
be set from 0.01 mL/min to 5.00 mL/min. However, for optimum
performance, set the flow rate to between 0.20 and 3.00 mL/min. Setting
the flow rate to 0.00 mL/min turns off the pump. For more information
about the pump, see

.

Injection Valve

The injection valve is a six-port, electrically-activated valve. For more
information about the injection valve, see

.

«
...
18
19
20
21
22
...
»

Содержание Dionex Easion































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dionex Easion

Бренд: ABB Страницы: 86

Бренд: MacDon Страницы: 17

Бренд: Olympus Страницы: 50

Бренд: VAHVA Страницы: 19

Бренд: Hanil Страницы: 60

Бренд: Parata Страницы: 40

Бренд: 1010music Страницы: 2

Бренд: 1010music Страницы: 4

Бренд: Panlux Страницы: 2

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: TANACOM Страницы: 27

Бренд: iBACheck Страницы: 2

Бренд: UEi Страницы: 5

Бренд: UGO BASILE Страницы: 47

Бренд: UFO Страницы: 16

Бренд: M-Audio Страницы: 48

Бренд: M-Audio Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды