Thermo Scientific Dionex Easion Скачать руководство пользователя страница 95

Страница: 95 / 126

A • Specifications

Doc. 155028-01 08/20

A.6

Injection Valve

A.7

Suppressors

Vacuum

Degasser

Optional with external vacuum degasser

Injection Valve

Two-position, six-port, electrically-activated Rheodyne valve

Chemical

Suppression

2 mm and 4 mm anion and cation

Displacement

Chemical

Regeneration

2 mm and 4 mm anion and cation

Suppression

Capacity

Dionex ACRS 500 (4 mm): 150



eq/min

Dionex ACRS 500 (2 mm: 37.5



eq/min

Dionex CCRS 500 (4 mm): 150



eq/min

Dionex CCRS 500 (2 mm): 37.5



eq/min

Void Volume

Dionex ACRS 500 (4 mm): <50



Dionex ACRS 500 (2 mm: <15



Dionex CCRS 500 (4 mm): <50



Dionex CCRS 500 (2 mm): <15



Sequential

Suppression for

Anions

With a Dionex CRS 500 and a Thermo Scientific

™

Dionex

™

Carbonate Removal Device:

•

The Dionex CRD 300 is designed for use with carbonate eluent-
based chemistries.

•

The Dionex CRD 200 is designed for use with hydroxide- and
borate-based chemistries.

Suppressor Wear

Parts

None; peristaltic pump and inline filters not required

Содержание Dionex Easion































































































































Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды

Thermo Scientific Dionex Easion, Руководство оператора

Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды