Thermo Scientific Dionex Easion Скачать руководство пользователя страница 79

Страница: 79 / 126

5 • Service

Doc. 155028-01 08/20

To install the new check valves:

1. Inspect the new inlet check valve

assembly (P/N 045722) to verify that the
double-hole end of the cartridge is
visible (see

Figure 5-5

If the double-hole end is not visible,
remove the cartridge from the housing
and install it correctly.

Inspect the new outlet check valve
assembly (P/N 045721) to verify that the
single-hole end of the cartridge is visible.

If the single-hole end is not visible,
remove the cartridge from the housing
and install it correctly.

Figure 5-5. Check Valve Assemblies

NOTE The pump will not operate properly unless the cartridge

is installed in the housing in the correct orientation.
Liquid flows through the check valve in the large single
hole and out the small double holes.

Figure 5-4. Pump Heads

Secondary

Pump Head

Primary
Pump Head

Outlet Check
Valve

Inlet Check
Valve

Double-hole

Single-hole

Flow

Inlet Check Valve

Outlet Check Valve

1/4-28 Port

10-32 Port

Содержание Dionex Easion































































































































Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды

Thermo Scientific Dionex Easion, Руководство оператора

Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды