Thermo Scientific Dionex Easion Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 126

background image

1 • Introduction

Doc. 155028-01 08/20

7

1.4.1

Notice on Lifting and Handling of Thermo Scientific
Instruments

For your safety, and in compliance with international regulations, the
physical handling of this Thermo Fisher Scientific instrument requires a
team effort to lift and/or move the instrument. This instrument is too
heavy and/or bulky for one person alone to handle safely.

1.4.2

Notice on the Proper Use of Thermo Scientific
Instruments

In compliance with international regulations: This instrument must be
used in the manner specified by Thermo Fisher Scientific to ensure
protections provided by the instrument are not impaired. Deviations from
specified instructions on the proper use of the instrument include changes
to the system and parts replacement. Accordingly, order replacement parts
from Thermo Fisher Scientific or one of its authorized representatives.

1.4.3

Notice on the Susceptibility to Electromagnetic
Transmission

Your instrument is designed to work in a controlled electromagnetic
environment. Do not use radio frequency transmitters, such as mobile
phones, in close proximity to the instrument.

For manufacturing location, see the label on the instrument.

1.4.4

WEEE Compliance

This product is required to comply with the European Union’s Waste
Electrical & Electronic Equipment (WEEE) Directive 2012/19/EU. It is
marked with the following symbol:

This symbol indicates that the equipment must not be thrown into general
waste and should be collected separately and processed in accordance
with local and state requirements.

«
...
13
14
15
16
17
...
»

Содержание Dionex Easion































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dionex Easion

Бренд: Ecco Страницы: 3

Бренд: Xoop Lighting Страницы: 20

Бренд: Vari Lite Страницы: 132

Бренд: Abicor Binzel Страницы: 92

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 15

Бренд: PASCO Страницы: 30

McDonnell & Miller PSE-800-M

Бренд: Xylem Страницы: 20

Бренд: popular Страницы: 27

Бренд: ABB Страницы: 136

Бренд: ABB Страницы: 108

Бренд: Beckman Coulter Страницы: 52

Бренд: Copernicus Страницы: 13

IQ Express RF6118

Бренд: Mainpine Страницы: 2

Бренд: Gomaco Страницы: 30

Бренд: Panduit Страницы: 4

Бренд: Woods Страницы: 54

Sportsman EXG 14/12

Бренд: M&R Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды