Thermo Scientific Dionex Easion Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 126

background image

C • TTL and Relay Control

Doc. 155028-01 08/20

95

c.

Connect the wires from the Dionex Easion connector plug to the TTL or
relay connector pins on the other module(s). Additional connector plugs
are provided with other Dionex modules.

NOTE Check the polarity of each connection. Be sure to

connect signal wires to signal (+) pins and ground
wires to ground (-) pins.

4. If you connected a TTL input, verify that the correct input control mode and

function are assigned to the input. Select different settings, if necessary (see

5. If you connected a TTL output that you want to have turned on and off with

the pump flow, select the

Flow Zero

option in the Chromeleon Instrument

Configuration Manager (see

C.2

Selecting TTL Input Control Modes and Functions

Follow the steps below to select a control mode and function for a TTL input.

1. Open the Chromeleon Instrument Configuration Manager.

2. In the Dionex Easion Properties

dialog box, click the

TTL Inputs

tab.

3. Double-click the TTL input name (or select the name) and press the

F2

key.

The Device Configuration dialog box for the selected input appears.

4. Select the preferred

Mode

and

Control Function

.

5. Click

OK

.

TTL Input Control Modes

The Dionex Easion TTL inputs respond to four types of signals. The default
control mode,

Normal Edge

, is compatible with the output signals provided by

Thermo Scientific Dionex modules.

If the device connected to the Dionex Easion does not send a normal edge signal,
select the appropriate control mode. Refer to the documentation provided with the
controlling device, as well as the information below, to select the correct type.

«
...
101
102
103
104
105
...
»

Содержание Dionex Easion































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dionex Easion

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: Raymarine Страницы: 90

Бренд: Bartscher Страницы: 61

LUXOMAT net PBM-KNX-DX-4W

Бренд: B.E.G. Страницы: 16

Бренд: Qlight Страницы: 4

Novation Launchkey Mini

Бренд: Focusrite Audio Engineering Страницы: 36

Бренд: Vitax Страницы: 12

Бренд: Strapack Страницы: 16

Бренд: Hameg Страницы: 60

Бренд: ebm-papst Страницы: 10

CEAG Exit Cube 33822 LED CGLine+

Бренд: Eaton Страницы: 20

Бренд: swamp Страницы: 5

Бренд: PMK Страницы: 24

Бренд: SteelFlex Страницы: 13

Бренд: ASIA TECHNOLOGY Страницы: 38

Бренд: KaVo Страницы: 70

Бренд: Slick Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды