Thermo Scientific Dionex Easion Скачать руководство пользователя страница 85

Страница: 85 / 126

5 • Service

Doc. 155028-01 08/20

3. If this is the

primary

pump head, install a 10-32 fitting plug (P/N 042772) on

the outlet check valve. Tighten the plug.

If this is the

secondary

pump head, install a 10-32 fitting plug (P/N 042772)

in both the inlet and outlet ports. Tighten the plugs.

4. Push the piston into the pump head. (This should hydraulically unseat the seal

from the head.) Remove the piston and pull off the seal.

NOTE If the piston seal is not removed, make sure the 10-32

fitting plug(s) are tight and add more water. Make sure
the pump head contains no air bubbles, and then repeat
Steps

and

5. Remove the 10-32 fitting plug(s).

To install the new piston seal:

1. If this is the

secondary

pump head, open the waste valve knob by turning the

knob one-half turn counterclockwise.

2. Lubricate the seal and the pump head

opening with a small amount of isopropyl
alcohol to facilitate insertion.

3. Push the piston through the spacer and

then through the new piston seal.

4. Insert the piston and seal into the pump

head.

Piston Seal

Spacer

Piston

Содержание Dionex Easion































































































































Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды

Thermo Scientific Dionex Easion, Руководство оператора

Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды