Thermo Scientific Dionex Easion Скачать руководство пользователя страница 89

Страница: 89 / 126

5 • Service

Doc. 155028-01 08/20

4. Orient the new seal (P/N 063382) with the grooved side away from the valve,

and slide it over the end of the valve.

5. Insert the valve with the new seal into the pump head opening and turn the

knob clockwise. Tighten finger-tight.

6. Turn on the Dionex Easion power switch.

7. Prime the pump (see

Section 3.6

5.11 Rebuilding the Injection Valve

Thermo Fisher Scientific recommends rebuilding the injection valve annually.
The Injection Valve Rebuild Kit (P/N 075973) contains all the required
replacement parts.

NOTE Substitution of non-Thermo Scientific/Dionex parts may

impair valve performance and void the product
warranty.

1. Click the pump

Off

button on the Chromeleon ePanel.

2. Open the front door of the Dionex Easion.

3. Disconnect each liquid line connected to the injection valve.

4. Follow the instructions provided in the Injection Valve Rebuild Kit to replace

the rotor seal, isolation seal, and stator face.

5. Reconnect all liquid lines to the injection valve.

6. Close the Dionex Easion front door.

7. Click the pump

button on the Chromeleon ePanel.

5.12 Replacing the Conductivity Cell

1. Turn off the Dionex Easion power switch.

2. Disconnect the power cord.

3. Open the Dionex Easion front door.

4. Disconnect the black

ELUENT OUT

line from the

ELUENT OUT

port on the

suppressor (see

Figure 5-10

Содержание Dionex Easion































































































































Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды

Thermo Scientific Dionex Easion, Руководство оператора

Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды