TELEDYNE API T300 Скачать руководство пользователя страница 10

Страница: 10 / 347

Table of Contents

Teledyne API – Model T300/T300M CO Analyzer

viii

4.1.2. Warning Messages ................................................................................................................................83

4.2.

Calibration Mode ..........................................................................................................................................84

4.3.

Setup MODE ................................................................................................................................................85

4.3.1. Password Security .................................................................................................................................85

4.3.2. Primary Setup Menu ..............................................................................................................................85

4.3.3. The areas accessible under the Setup mode are shown in Table 4-4 and Secondary Setup Menu

(SETUP>MORE) ...................................................................................................................................85

4.3.4. Secondary Setup Menu (SETUP>MORE) .............................................................................................86

5. SETUP MENU .................................................................................................................... 87

5.1.

SETUP

CFG: Configuration Information .................................................................................................87

5.2.

SETUP

ACAL: Automatic Calibration ......................................................................................................88

5.3.

SETUP

DAS: Internal Data Acquisition System .......................................................................................88

5.4.

SETUP

RNGE: Analog Output Reporting Range Configuration .............................................................88

5.4.1. Analog Output Ranges for CO Concentration .......................................................................................88

5.4.2. Physical Range vs Analog Output Reporting Ranges ...........................................................................90

5.4.3. Reporting Range Modes: Single, Dual, Auto Ranges ...........................................................................90

5.4.3.1. SINGLE Range Mode (SNGL) .......................................................................................................92

5.4.3.2. DUAL Range Mode (DUAL) ...........................................................................................................93

5.4.3.3. AUTO Range Mode (AUTO) ..........................................................................................................95

5.4.4. Range Units ...........................................................................................................................................97

5.4.5. Dilution Ratio (Option) ............................................................................................................................98

5.5.

SETUP

PASS: Password Protection .......................................................................................................99

5.6.

SETUP

CLK: Setting the Internal Time-of-Day Clock and Adjusting Speed .........................................101

5.6.1.1. Setting the Internal Clock’s Time and Day ...................................................................................101

5.6.1.2. Adjusting the Internal Clock’s Speed ............................................................................................101

5.7.

SETUP

Comm: Communications Ports .................................................................................................103

5.7.1. ID (Machine Identification) ...................................................................................................................103

5.7.2. INET (Ethernet) ....................................................................................................................................103

5.7.3. COM1 and COM2 (Mode, Baud Rate and Test Port) ..........................................................................103

5.8.

SETUP

VARS: Variables Setup and Definition ......................................................................................104

5.9.

SETUP

Diag: Diagnostics Functions ......................................................................................................106

5.9.1. Signal I/O .............................................................................................................................................108

5.9.2. Analog Output ......................................................................................................................................109

5.9.3. Analog I/O Configuration ......................................................................................................................110

5.9.3.1. Analog Output Voltage / Current Range Selection .......................................................................112

5.9.3.2. Analog Output Calibration ............................................................................................................114

5.9.3.3. Enabling or Disabling the AutoCal for an Individual Analog Output .............................................114

5.9.3.4. Automatic Calibration of the Analog Outputs ...............................................................................116

5.9.3.5. Individual Calibration of the Analog Outputs ................................................................................117

5.9.3.6. Manual Calibration of the Analog Outputs Configured for Voltage Ranges .................................118

5.9.3.7. Manual Adjustment of Current Loop Output Span and Offset .....................................................120

5.9.3.8. Turning an Analog Output Over-Range Feature ON/OFF ...........................................................123

5.9.3.9. Adding a Recorder Offset to an Analog Output ............................................................................124

5.9.3.10. AIN Calibration ...........................................................................................................................125

5.9.3.11. Analog Inputs (XIN1…XIN8) Option Configuration ....................................................................126

5.9.4. Electrical Test ......................................................................................................................................127

5.9.5. Dark Calibration ...................................................................................................................................127

5.9.6. Pressure Calibration ............................................................................................................................127

5.9.7. Flow Calibration ...................................................................................................................................128

5.9.8. Test Chan Output .................................................................................................................................128

5.9.8.1. Selecting a Test Channel Function for Output A4 ........................................................................128

5.10.

SETUP

ALRM (Option): Using the Gas Concentration Alarms ...........................................130

5.10.1. Setting the T300 Concentration Alarm Limits ....................................................................................131

6. COMMUNICATIONS SETUP AND OPERATION ............................................................. 133

6.1.

Data Terminal/Communication Equipment (DTE DCE) .............................................................................133

06864D DCN7562

Содержание T300




























































































































































































































































































































































Результаты поиска

Содержание T300

Отзывы:

Похожие инструкции для T300

Бренды по названию

Популярные бренды

TELEDYNE API T300, Руководство по эксплуатации

Результаты поиска

Содержание T300

Отзывы:

Похожие инструкции для T300

Бренды по названию

Популярные бренды