TELEDYNE API T300 Скачать руководство пользователя страница 97

Страница: 97 / 347

Teledyne API – Model T300/T300M CO Analyzer

Setup Menu

5.4.3.3.

AUTO RANGE MODE (AUTO)

AUTO

range mode, the analyzer automatically switches the reporting range between

two user-defined ranges (low and high).

•

The unit will switch from low range to high range when the CO

concentration

exceeds 98% of the low range span.

•

The unit will return from high range back to low range once both the CO

concentration falls below 75% of the low range span.

AUTO

Range Mode the instrument reports the same data in the same range on both

the

and

outputs and automatically switches both outputs between ranges as

described above. Also the

RANGE

test function displayed on the front panel will be

replaced by two separate functions:

•

RANGE1

: The

LOW

range setting for all analog outputs.

•

RANGE2

: The

HIGH

range setting for all analog outputs.

The high/low range status is also reported through the external, digital status bits (See
Section 3.3.1.4).

06864D DCN7562

Содержание T300




























































































































































































































































































































































Результаты поиска

Содержание T300

Отзывы:

Бренды по названию

Популярные бренды

TELEDYNE API T300, Руководство по эксплуатации

Результаты поиска

Содержание T300

Отзывы:

Бренды по названию

Популярные бренды