Tektronix TLA7AA1 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 173

Tektronix TLA7AA1 Скачать руководство пользователя страница 54

Operating Information

TLA7AXX Logic Analyzer Module Service Manual

2- 11

Figure 2--7 shows the connectors and controls on the rear panel of the logic
analyzer module.

P1 Connector

P2 Connector

Logical address

switches

Figure 2- 7: Rear panel controls and connectors

P1 and P2 Connectors.

The acquisition board and the local processor unit (LPU)

provide the electrical connections from the module to the mainframe. These
electrical connections include power distribution, processor communications,
and intermodule communications.

Logical Address Switches.

The logical address switches determine the logical

address of the module. These switches should normally be set to address FF. For
more information on these switches and their settings, refer to

Logical Address

on page 2--1.

Most user information for operating the logic analyzer module is available
through the online help within the logic analyzer application. You can select the
online help from the pull-down help menu, by clicking the Help button in a
dialog box, or by using the what’s this help (click the question mark icon, drag
the cursor to the item of interest on the screen, and then release the mouse
button).

The logic analyzer module performs power-on diagnostics each time you power
on the mainframe. The Calibration and Diagnostics property sheet appears at
power-on if one or more of the diagnostics fail.

For more detailed tests, you can execute the extended diagnostics or the self
calibration. For more information on the diagnostics, refer to

Calibration and

Diagnostic Procedures

beginning on page 6--29.

NOTE

. For best results, only run the diagnostics with the probes disconnected

from the module.

Rear Panel

Online Help

Diagnostics

«
...
52
53
54
55
56
...
»

Содержание TLA7AA1














































































































































































Отзывы:

Нет отзывов