Tektronix TLA7AA1 Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 173

Tektronix TLA7AA1 Скачать руководство пользователя страница 133

Removal and Installation Procedures

6- 14

TLA7AXX Logic Analyzer Module Service Manual

1

2

Figure 6- 6: Installing the cover onto the chassis

3.

Make sure that the cover is fully seated (no gaps) against the front and rear
chassis flanges (see Figure 6--7).

4.

While holding the cover in place, install the four T-10 Torx-drive screws
nearest the front of the module (two on each side of the cover), to secure the
cover to the chassis.

5.

Slide the rear panel on the chassis and install the two rear panel T-10
Torx-drive screws.

6.

Gently squeeze the chassis flange and rear panels flange together while
tightening the screws on the sides. This ensures that the rear panel does not
rotate, otherwise the module may not seat properly when installed in the
mainframe.

7.

Install the two remaining T-10 Torx-drive screws nearest the rear of the
module (one on each side of the cover).

8.

Place the cover onto the chassis.

9.

If your instrument has a merge cable, complete the following steps to install
the merge cable assembly:

a.

Feed the merge cable through the cover.

b.

Carefully connect the merge cable to the circuit board (refer to Fig-
ure 6--4 on page 6--12 as necessary).

c.

Insert the bracket assembly into the hole in the cover.

d.

Install the eight T-9 countersunk screws on the bracket.

«
...
131
132
133
134
135
...
»

Содержание TLA7AA1














































































































































































Отзывы:

Нет отзывов