Tektronix TLA7AA1 Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 173

Tektronix TLA7AA1 Скачать руководство пользователя страница 130

Removal and Installation Procedures

TLA7AXX Logic Analyzer Module Service Manual

6- 11

Use the following procedure and Figure 6--3 to install the injector/ejector
handles:

NOTE

. The top and bottom injector/ejector handles are not interchangeable. The

top injector/ejector handle assembly has a notch on right side and a tab on the
left side; the bottom injector/ejector handle assembly does not have a notch or a
tab.

1.

Install the injector/ejector handle through the front panel cutout onto the
mounting post.

2.

Install the screws to secure the injector/ejector handle to the chassis.

3.

Apply the proper replacement label (see the

Replaceable Mechanical Parts

List

for label part numbers if necessary).

Covers

You will need a screwdriver with a T-9 and a T-10 tip to complete the following
procedures.

Use the following procedure and Figures 6--4 and 6--5 to remove the covers:

1.

Place the module on the right side.

2.

Remove the two screws on the rear of the chassis and the two rear screws,
located on either side of the rear panel, that secure the rear panel to the
chassis.

3.

Remove the rear panel and set it aside.

4.

Remove the two top screws and the two bottom screws that secure the cover
to the chassis.

5.

If you have a 102-channel module or a 136-channel module with a merge
cable, complete to following steps (refer to Figure 6--4 as necessary):

a.

Remove the eight T-9 countersunk screws holding the bracket to the
cover.

b.

Lift the assembly out of the cover and then reach into the hole and
disconnect the merge cable from the circuit board.

6.

Slide the cover back to disengage the tab and lift the cover from the chassis.

Installation

Removal

«
...
128
129
130
131
132
...
»

Содержание TLA7AA1














































































































































































Отзывы:

Нет отзывов