Tektronix TLA7AA1 Скачать руководство пользователя страница 132

Страница: 132 / 173

Removal and Installation Procedures

TLA7AXX Logic Analyzer Module Service Manual

6- 13

Screws (3)

Screws (2)

Rear panel

Chassis

Cover

Figure 6- 5: Cover removal

Use the following procedure and Figures 6--4 through Figure 6--7 to install the
covers:

NOTE

. Install the cover tightly against the chassis. This will ensure that the

module fits into adjacent slots in the mainframe.

Place the module on its right side.

CAUTION.

To prevent damage to the module during the installation process,

reinstall the cover exactly as described in steps 2 through 8.

If the cover is not properly seated, the module can be damaged when you install
it in a mainframe.

Insert the cover at an angle (step 1 in Figure 6--6) such that the front edge of
the cover engages with the EMI gaskets on the back of the front panel. Then
push the rear of the cover in place (step 2 Figure 6--6).

Installation

Содержание TLA7AA1














































































































































































Результаты поиска

Содержание TLA7AA1

Отзывы:

Tektronix TLA7AA1, Руководство пользователя, Страница: 132 / 173

Результаты поиска

Содержание TLA7AA1

Отзывы: