Tektronix TLA7AA1 Скачать руководство пользователя страница 109

Страница: 109 / 173

Adjustment Procedures

5- 8

TLA7AXX Logic Analyzer Module Service Manual

Figure 5- 3: Default Adjustment procedure dialog box

Select the probe type near the bottom of the dialog box.

Select the Probe Gain & Offset procedure (the default selection is not
selected); clear any other procedures.

NOTE

. The software will perform all selected procedures in the listed sequence.

To limit the test to specific procedures, clear any procedures that you do not
want to run.

Click the Next button at the bottom of the dialog box to begin the adjustment
procedure.

A list of connection instructions displays for the current procedure.

Verify that your connections match those of the instructions. Then click the
Next button to begin the adjustment procedures.

The software will begin the adjustment procedures and display a list of
results in the window.

Содержание TLA7AA1














































































































































































Результаты поиска

Содержание TLA7AA1

Отзывы:

Tektronix TLA7AA1, Руководство пользователя, Страница: 109 / 173

Результаты поиска

Содержание TLA7AA1

Отзывы: