Tektronix TLA7AA1 Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 173

Tektronix TLA7AA1 Скачать руководство пользователя страница 125

Maintenance

6- 6

TLA7AXX Logic Analyzer Module Service Manual

Cleaning the P6860 and P6880 Compression Footprints

CAUTION.

To avoid electrical damage, always turn off the power of your target

system before cleaning the compression footprint.

Prior to connecting the probe to the target system, the compression footprints on
the target system must be properly cleaned. Clean the compression footprints
according to the following steps:

1.

Use a lint-free cloth moistened with isopropyl alcohol and gently wipe the
footprint surface.

2.

Remove any remaining lint using a nitrogen air gun.

NOTE

. Use alcohol sparingly and be sure that you have removed any remaining

lint or residue with the nitrogen air gun.

Cleaning the P6860 and P6880 Probe Heads

Before connecting the P6860 and P6880 Probes to the target system, ensure that
the probe heads are free from dust, dirt, and contaminants. If necessary, clean the
probe heads according to the following steps.

CAUTION.

Static discharge can damage semiconductor components in the probe

head. Always wear a grounded antistatic wrist strap whenever handling the
probe head. Also verify that anything to which the probe head is connected does
not carry a static charge.

NOTE

. Never clean the elastomers. Always replace them instead. Refer to the

Operating Basics

chapter of the

P6810, P6860, & P6880 Logic Analyzer Probe

Instruction Manual

for information on replacing elastomers.

1.

Remove elastomer holder (see Figure 6--1).

2.

Moisten a cotton swab with isopropyl alcohol.

«
...
123
124
125
126
127
...
»

Содержание TLA7AA1














































































































































































Отзывы:

Нет отзывов