Tektronix TLA7AA1 Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 173

Tektronix TLA7AA1 Скачать руководство пользователя страница 142

Removal and Installation Procedures

TLA7AXX Logic Analyzer Module Service Manual

6- 23

Fuses

There are no user-replaceable parts on any of the circuit boards. If you suspect
that an open fuse exists, there is no easy way of determining the cause of the
open fuse. Most of the fuses are surface mounted and attempting to change the
fuses with improper tools will result in damaging the circuit boards beyond
repair. You should return the circuit board to you local Tektronix service center
for corrective action.

Front and Rear EMI Gaskets

Use the following procedure to remove the front and rear EMI gaskets:

1.

Perform the

Cover

removal procedure (see page 6--11).

2.

For the front EMI gaskets:

a.

Locate the gasket to be replaced.

b.

Lift the gasket fingers and rotate the gasket off.

3.

For the two rear gaskets on the chassis

a.

Perform the

Local Processor Unit Board

removal procedure (page 6--16),

and the

Acquisition Board

removal procedure (page 6--19).

b.

Lift the gasket fingers and rotate the gasket off (see Figure 6--13).

Lift gasket finger

1

Rotate

2

Figure 6- 13: Rear EMI gasket removal

Removal

«
...
140
141
142
143
144
...
»

Содержание TLA7AA1














































































































































































Отзывы:

Нет отзывов