Tektronix TLA7AA1 Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 173

Tektronix TLA7AA1 Скачать руководство пользователя страница 121

Maintenance

6- 2

TLA7AXX Logic Analyzer Module Service Manual

H

Nothing capable of generating or holding a static charge should be allowed
on the work surface.

H

Handle circuit boards by the edges when possible.

H

Do not slide the modules over any surface.

H

Avoid handling the modules in areas that have a floor or work surface
capable of generating a static charge.

Inspection and Cleaning

Inspection and cleaning are done as preventive maintenance. Preventive
maintenance, when done regularly, may prevent malfunctions and enhance
reliability.

Preventive maintenance consists of visually inspecting and cleaning the
instrument, and using general care when operating it. How often to perform
maintenance depends on the severity of the environment in which the instrument
is used. A proper time to perform preventive maintenance is just before
performing performance verification procedures or as an incoming inspection.

The side cover keeps dust out of the instrument and should be in place during
normal operation.

Inspect and clean the instrument as often as operating conditions require.
Collection of dirt on internal components can cause them to overheat and
breakdown. Dirt acts as an insulating blanket, preventing efficient heat dissipa-
tion. Dirt also provides an electrical conduction path that can cause failures,
especially under high-humidity conditions.

CAUTION.

Avoid using chemical cleaning agents that might damage the plastics

and external labels used in the instrument.

Use a cloth dampened with water to clean external surfaces. To prevent damage
to electrical components from moisture during external cleaning, use only
enough liquid to dampen the cloth or applicator.

Use a 75% isopropyl alcohol solution to clean internal surfaces and rinse with
deionized water. Before using any other type of cleaner, consult your Tektronix
Service Center or representative.

General Care

Inspection and Cleaning

Procedures

«
...
119
120
121
122
123
...
»

Содержание TLA7AA1














































































































































































Отзывы:

Нет отзывов