Tektronix TLA7AA1 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 173

Tektronix TLA7AA1 Скачать руководство пользователя страница 102

TLA7AXX Logic Analyzer Module Service Manual

5- 1

Adjustment Procedures

This chapter contains procedures which use the performance verification
software to adjust the logic analyzer modules to within factory specifications.
The software contains instructions and control programs for adjusting the logic
analyzer. The software describes test equipment connections and settings, selects
setup parameters, and loads calibration constants into memory.

NOTE

. There are no adjustment procedures for the TLACAL2 Performance

Verification test fixture in this section. If the test fixture requires any adjustments,
you must return the test fixture to the factory; contact your local Tektronix
service center for more information.

These procedures adjust the logic analyzer module for conformance with the
warranted characteristics listed in the

Specifications

chapter of this manual.

Perform the adjustments after repairing the module or when performance
verification tests have failed.

Test Equipment and Initial Setup

The adjustment procedures use the same test equipment and setups as listed in
the Performance Verifications chapter. Refer to those sections for additional
information before starting the adjustment procedures.

Prerequisites

NOTE

. The performance verification software reads the serial number of the

logic analyzer module from information stored in the LPU board. If you have
replaced the LPU board, verify that the serial number on the label of the module
matches the serial number read by the software before beginning the adjustment
procedures.

«
...
100
101
102
103
104
...
»

Содержание TLA7AA1














































































































































































Отзывы:

Нет отзывов