TechnipFMC Smith Meter MPU 1600c Скачать руководство пользователя страница 56

Страница: 56 / 120

Page 56 • MNKS025 ║ Issue/Rev. 0.1 (11/18)

MPU Series C I/O/M Manual

Web User Interface

6.4.2.9.12. Enable Confidence Alarms

The confidence alarms provide an indication of the measurement quality for a number

of meter outputs. These alarms output through Modbus measurement health status

word only.
The input to enable the alarm is in the format of an eight bit integer that can be used to

mask specific bits from activating if desired. Enter the integer value of the binary mask

to enable the alarms. A value of zero disables all alarms and 31 (bin 11111) enables all

five alarm bits.
The following alarms are available:

Bit

Process Variable

Description

Flow Rate

Flow rate output quality alarm

Velocity of Sound

Velocity of sound quality alarm

Density

Density computation quality alarm

Viscosity

Viscosity computation quality alarm

Reynolds Number

ReNo computation quality alarm

Analog Output

Analog output quality alarm

Bit

Process Variable

Description

Flow Rate

Flow rate output quality alarm

6.4.2.10. Modes

(Path: Settings > Modes)

6.4.2.10.1. Disable Paths

(Path: Settings > Modes > Disable Paths)

This option will disable a particular path and replace its flow profile factor value with an

internally calculated substitution.
• Input Field – desired path state (1 = disabled/substitution)

6.4.2.10.2. Manual Values

(Path: Settings > Modes > Manual Valves)

This option places the meter into a simulation (non-measured) type mode. Be aware

that measured values are not displayed while this mode is enabled.
Options:
• Disabled
• Enabled

Содержание Smith Meter MPU 1600c

























































































































Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Похожие инструкции для Smith Meter MPU 1600c

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter MPU 1600c, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Похожие инструкции для Smith Meter MPU 1600c

Бренды по названию

Популярные бренды