TechnipFMC Smith Meter MPU 1600c Скачать руководство пользователя страница 23

Страница: 23 / 120

Issue/Rev. 0.1 (11/18) ║ MNKS025 • Page 23

MPU

Series

I/O/M

Manual

Operation

3.9.1.1. Equipment Required

• Conventional hand tools for cable installation.
• If a fiber optic cable is a part of the delivery, special tools for connecting ST-connectors

are required.

CAUTION:

To prevent ignition of hazardous atmospheres, disconnect from supply circuit

before opening, keep tightly closed when circuits are in operation.

WARNING:

Contains internal battery-powered circuit. In order to prevent ignition of haz-

ardous atmospheres, do not open enclosure unless area is known to be non-hazardous.

3.9.1.2. Cable Installation Check List

1. All cables to and from the MPU are connected to dedicated terminals in the electronic

enclosure.

2. Check that the connection of armor and screens are done according to the drawings

and relevant specifications. General descriptions for installation of the various power

or signal types are shown below. Keep in mind various types of cable glands and how

these should be installed.

3. The cable must be installed on cable trays or in pipes, protected against mechanical

damage.

4. The external cables are entered into the Ex d enclosure, and relevant regulations for

such installation must be followed. Keep in mind minimum segregation between power

and signal cables.

5. Be aware of the minimum bending radius of the cable. The bending radius for a

multi-core cable is normally 6 times the diameter, but may vary so cable specifications

must be checked.

6. Make sure that the earthing system is maintained. The Protective Earth (PE) bars

have to be connected to the main earth system.

7. Make sure that the Cortech or similar is removed from the connection box before

power is switched on.

8. All cable armor or cable shield connections should be as short as possible, reduce

“pigtails” to a minimum.

Содержание Smith Meter MPU 1600c

























































































































Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Похожие инструкции для Smith Meter MPU 1600c

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter MPU 1600c, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Похожие инструкции для Smith Meter MPU 1600c

Бренды по названию

Популярные бренды