TechnipFMC Smith Meter MPU 1600c Скачать руководство пользователя страница 96

Страница: 96 / 120

Page 96 • MNKS025 ║ Issue/Rev. 0.1 (11/18)

• Select Secondary URL

•

Ensure no data is entered in the dialog box

•

Press green accept button

• Press down arrow in upper right hand corner

• Select Secondary Timeout

•

Ensure 0 is entered in the dialog box

•

Press green accept button

• Select the back button in the upper left hand corner of the display

• SUCCESS message is displayed. Touch the display anywhere to acknowledge

the success message.

3. Change the display passwords.
4. Change the display electronic seal state parameter to “Sealed”.

• Select

Information

• Verify that the Parameter Seal shows a closed lock

• Select the back button in the upper left hand corner of the display

• Select

Maintenance

• Select reset passwords

•

Press green accept button

• Verify that an error message is displayed, “Failed to reset passwords

because no flash drive found.” Touch the display anywhere to

acknowledge the message.

• Select the back button in the upper left hand corner of the display

5. Verify the connection parameters only allow the display to connect with devices that

are part of the Legally Relevant system.

• Select Reconnect

• Write down the serial number of the meter that is shown in the upper right

hand corner of the display.

• Note that you can also select the Meter Information Screen and the serial number

is displayed in the General category of that page.

• For a remote display, cycle power to the display.

• For a local display (where the display is the front panel of the meter), cycle main

power.

• When power is restored the display will automatically connect to the meter.

• Verify that the meter serial number written down previously is the same number

as is now shown (after the power cycle) in the upper right hand corner of the

display.

MPU Series C I/O/M Manual

Integrated Touch Screen Display

Содержание Smith Meter MPU 1600c

























































































































Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter MPU 1600c, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Бренды по названию

Популярные бренды