TechnipFMC Smith Meter MPU 1600c Скачать руководство пользователя страница 28

Страница: 28 / 120

Page 28 • MNKS025 ║ Issue/Rev. 0.1 (11/18)

MPU Series C I/O/M Manual

UMCB – Ultrasonic Meter Control Board

NOTE:

Reference the product specification sheets for technical specifications of the I/O.

Note in diagrams below:

Customer Wiring / Equipment

4.1.3.

Digital I/O

Connections for the digital I/O are made on the UMCB board using terminal CN2 and CN3

4.1.4.

Digital/Pulse Output

The pulse output connections are made using terminal CN3 as follows:

Function

Connection Port

Digital/Pulse Out #1

CN3 - Terminal 4 and 6

Digital/Pulse Out #2

CN3 - Terminal 5 and 6

Pulse Out #2 is 90 electrical degrees out of phase with Pulse Out #1.

For forward flow, Pulse Out #2 lags Pulse Out #1.
For reverse flow, Pulse Out #2 leads Pulse Out #1.

The pulse outputs can be configured to act as active outputs or pseudo open collectors.

They are “pseudo” because the two output grounds are not isolated from each other.

4
5

CN3

ISO GND

Digital Outputs - Active Output Mode - Preferred

GND

Digital/Pulse Input

Unregulated

+VDC

(from CN1)

SW600

SYS

GND

ISO

GND

- OR -

Note:

Customer can power Active Outputs with higher or lower

voltage by setting both positions of SW600 to OFF and connecting

external power supply between CN3 Positions 3 and 6.

Note: If using dual pulse output the two conductors carrying the

outputs must not be in the same pair and ideally are individually

shielded.

EARTH

*Out2/B is wired identically between Positions 5 and 6

GND

Digital/Pulse Input

CN3

ISO GND

Unregulated

+VDC

(from CN1)

SW600

SYS

GND

ISO

GND

EARTH

GND

NOTE:

Customer can power Active Outputs with higher or lower voltage by setting both

positions of SW600 to OFF and connecting external power supply between CN3

positions 3 and 6.

NOTE:

If using dual pulse output the two conductors carrying the outputs must not be

in the same pair and ideally are individually shielded.

Содержание Smith Meter MPU 1600c

























































































































Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter MPU 1600c, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Бренды по названию

Популярные бренды