TechnipFMC Smith Meter MPU 1600c Скачать руководство пользователя страница 35

Страница: 35 / 120

Issue/Rev. 0.1 (11/18) ║ MNKS025 • Page 35

MPU Series C I/O/M Manual

Meter Start-Up

5 – Meter Start-Up

Before powering on the meter and beginning flow measurement, verify that the

following items are completed:
• Meter has been properly installed (flow direction is correct) in the piping and all

connections are free from leaks.

• Power Supply, Input / Output connections have been checked for proper wiring

and connection integrity.

• All conduit and/or gland connections are in adherence to applicable electrical

codes.

When power is applied to the meter, it will go through a boot sequence and will then

begin measurement automatically. This process takes several seconds. If flow is pres-

ent, the pulse output will begin and the connected flow computer should begin totalizing.

If power is interrupted for a period of less than 20 ms during operation, the meter will

continue operating with no loss of measurement. If power is lost for more than 100 ms

during operation, the meter will reset. Once power is re-supplied, the Ultra Series meter

will go through the power-on boot sequence and will resume measurement.

5.1.

LEDs Overview

During start-up and normal operation four LEDs on the UMCB board above the

ETH2 connector are visible and intended to communicate status information.

The LEDs consist of:

•   LED 200 - Blue
•   LED 201 - Green
•   LED 202 - Yellow
•   LED 203 - Red

Electronics Meter Serial #

Содержание Smith Meter MPU 1600c

























































































































Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Похожие инструкции для Smith Meter MPU 1600c

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter MPU 1600c, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Похожие инструкции для Smith Meter MPU 1600c

Бренды по названию

Популярные бренды