TechnipFMC Smith Meter MPU 1600c Скачать руководство пользователя страница 7

Страница: 7 / 120

Issue/Rev. 0.1 (11/18) ║ MNKS025 • Page 7

MPU

Series

I/O/M

Manual

General

1.2.1.

Hints for Installation in Hazardous Area

All the components marked with the sign of

are explosion-proof electrical equipment

and safety-tested and certified. See section 3.8 for electrical installation.

Caution:

Any interference, mechanical or electrical, is not permitted.

EX-protection regulations must be observed!

In case of a malfunction of the electronic board fitted in the flameproof housing only the

complete board has to be replaced. Test and repair of the board is only possible in the

factory. The installation and replacement of the board is the task of skilled personnel.

General hints:
• The electrical installation has to be compliant with EN 60079-14 and the ordinary

electric installation rules.

• To prevent ignition of hazardous atmospheres and to prevent electrical shock,

disconnect from supply circuits before opening. Protect the device against

unintended power on. Before bringing the device into operation make sure that it

is tightly closed.

• The flameproof housing contains one or more of the following threaded entries:

½” NPT. All cable entries, stopping boxes or plugs shall be certified according to

the requirements in EN / IEC 60079-1.

• The flameproof housing contains an internal battery-powered circuit. Do not open

the housing unless an area is known to be non-hazardous. To reduce the risk of

ignition of hazardous atmospheres, conduit runs must have a sealing fitting

connected within 45 cm of the enclosure.

• Before the first power up after installation check that the connected voltage is

conform to power rating on the name plate. Not used cable entries have to be closed

with certified plugs.

• The wiring has to be made according to the wiring diagrams which are part of this

manual.
• Modification of the internal construction of the flameproof and adding additional

parts to the electronic are not allowed

• Special precaution must be made when bringing the supplied Laptop / PC into

hazardous area. Provide for work permit before bringing the Laptop / PC into

restricted area, according the site regulations. A gas detector must be in operation

continuously while the Laptop / PC is present in the restricted area. This applies

also while it is switched off.

1.2.2.

Danger from High Pressure and Explosive Gas

The MPU is directly integrated into gas-carrying pipelines. The operating company shall

be responsible for safe operation and for complying with additional national regulations.

Содержание Smith Meter MPU 1600c

























































































































Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Похожие инструкции для Smith Meter MPU 1600c

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter MPU 1600c, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Smith Meter MPU 1600c

Отзывы:

Похожие инструкции для Smith Meter MPU 1600c

Бренды по названию

Популярные бренды